Specs for the Air Lift Ride Control Air Helper Springs # AL59561

Question

Question:

Can you provide the following specs on this air bag? Inflation port size: Compressed height: Extended height: Ride height range: Maximum diameter: Maximum PSI:

asked by: Travis K

0

Expert Reply:

The Air Lift Ride Control Air Helper Springs # AL59561 has the following specs:

Inflation port size: 1/8" NPT
Compressed height: 2.4"
Extended height: 7"
Ride height range: 4" - 6"
Maximum diameter: 4.6"
Maximum PSI: 100 psi (Minimum is 5 psi)

I confirmed this with my contact at Air Lift.

expert reply by: Jon G

0

Answer 1

I have some information that will help us determine if the air bags included with the Air Lift Ride Control Helper Springs, #AL59561, will work for you, however, we have not received any complaints of these air bags being too tall or causing fit…

view full answer...

Answer 2

The picture you have submitted looks like it is behind the rear axle on the passengers side like you have said but this is not where the the Air Lift air bags, #AL59561, will install. They will install forward of the rear axle but that portion of the…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 10

I highly recommend going with the Air Lift LoadLifter 5000 Air Helper Springs #AL49DQ over their Ride Control system for your 2023 Toyota Tacoma 4WD because they not only offer more support, but they also have a better construction so they'll…

view full answer...

Answer 11

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 12

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...