Overall Length of Replacement Stabilizer Bar # RM-B001225

Question

Question:

how long is part number RM B00 1225, stabilizer bar, From bolt hole center to bolt hole center?

asked by: Jon

0

Expert Reply:

I checked with Roadmaster and the overall length of the Replacement Stabilizer Bar # RM-B001225 is 35-3/4 inches.

This is designed as a replacement part for the tow dolly part # RM-2050-1 which wouldn't require measuring to determine the fit of. So as long as you have the # RM-2050-1 this will be exactly what you'd need.

expert reply by: Jameson C

0

click to enlarge

Denis L.

7/5/2020

I would like to know the torque pressure of the bolts at each end of this stabilizer bar...Should the bolts mounted at the axle be very tight ?.. My dolly is hard to make tilt..maybe the bolts are too tight Thank you

Reply

Chris R.

7/9/2020

The installation manual for the Roadmaster Dolly don't provide specific torque specs for the stabilizer bar hardware, but they do explain how to tighten them correctly (so that it actually tilts). The following is directly from the manual: If the ramps tilt down under their own weight, tighten the bolts further. Repeat until the ramps will not tilt down under their own weight.Then loosen the bolts slightly. When the ramps just begin to tilt down after you remove the pivot pin, the bolts are tightened correctly

Reply

Answer 1

The stabilizer bar, part #RM-921006, is 42 inches end to end and 40 inches from the bolt holes center on center.

view full answer...

Answer 2

I checked with Roadmaster and the overall length of the Replacement Stabilizer Bar #RM-B001225 overall is 35-3/4 inches.

view full answer...

Answer 3

I attached the install instructions and owners manual for the Roadmaster Tow Dolly part #RM-2050-1 that you referenced. They are linked on this page under the words, "Featured Help Information."

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Overall Length of Replacement Stabilizer Bar # RM-B001225

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching