Measurements For The Replacement Stabilizer Bar For Roadmaster Tow Dolly

Question

Question:

what is the length and size of the bar?

asked by: Ray S

0

Expert Reply:

The stabilizer bar, part # RM-921006, is 42 inches end to end and 40 inches from the bolt holes center on center.

expert reply by: Bryce D

0

Bar Measurements
(click to enlarge)

Answer 1

I checked with Roadmaster and the overall length of the Replacement Stabilizer Bar #RM-B001225 overall is 35-3/4 inches.

view full answer...

Answer 2

I checked with Roadmaster and the overall length of the Replacement Stabilizer Bar #RM-B001225 is 35-3/4 inches. This is designed as a replacement part for the tow dolly part #RM-2050-1 which wouldn't require measuring to determine the fit of. So…

view full answer...

Answer 3

I attached the install instructions and owners manual for the Roadmaster Tow Dolly part #RM-2050-1 that you referenced. They are linked on this page under the words, "Featured Help Information."

view full answer...

Answer 4

The hardware needed to attach the Replacement Stabilizer Bar part #RM-B001225 to the Roadmaster Tow Dolly with Electric Brakes part #RM-2050-1 is not included nor is this something that Roadmaster offers separately. That said, all you would need to…

view full answer...

Answer 5

I spoke with my contact at Roadmaster and he said that on a Roadmaster Tow Dolly Trailer like the #RM-2050-1, the serial number will be located on the tongue of the trailer or on the passenger side, main base, facing forward.

view full answer...

Answer 6

I may have an option for you but we only carry stabilizer bars for the Roadmaster Tow Dolly RM-2000-1 and RM-2050-1. If you have the former you'll need the Replacement Stabilizer Bar part #RM-921006 or if you have the latter you'll need the…

view full answer...

Answer 7

With a tow bar such as #63180 you will have to have the toad lined up straight behind the RV to even attach it to the brackets on the toad. So the process of actually connecting the vehicle to the RV ensures that it is lined up straight. On tow bars…

view full answer...

Answer 8

I went out and took some measurments for you and found that the Replacement Steering Pin and Clip for Roadmaster Tow Dollies #RM-357100-00 is approximately 5-1/2 inches long (4-1/2 inch usable length) by 5/8 inch diameter. I have included a few other…

view full answer...

Answer 9

In regards to the Roadmaster Tow Dolly Ramp Wear Strip and Spacer Plate Replacement Kit part #RM-2000-25, the instructions state to "Apply the supplied lubricant to the top of the replacement deck spacer and the two replacement ramp wear…

view full answer...

Answer 10

Yes, they are made of wood. No, but the Roadmaster Tow Dolly Ramp Wear Strip and Spacer Plate Replacement Kit part #RM-2000-25 aren't an upgrade, they are the same wear plate that would have came with the trailer when purchased new. They are made…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Measurements For The Replacement Stabilizer Bar For Roadmaster Tow Dolly

Product Page this Question was Asked From

Continue Researching