How Long is Replacement Stabilizer Bar # RM-B001225

Question

Question:

whats the length of the stabalizer bar? ty

asked by: Tony L

0

Expert Reply:

I checked with Roadmaster and the overall length of the Replacement Stabilizer Bar # RM-B001225 overall is 35-3/4 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The stabilizer bar, part #RM-921006, is 42 inches end to end and 40 inches from the bolt holes center on center.

view full answer...

Answer 2

I checked with Roadmaster and the overall length of the Replacement Stabilizer Bar #RM-B001225 is 35-3/4 inches. This is designed as a replacement part for the tow dolly part #RM-2050-1 which wouldn't require measuring to determine the fit of. So…

view full answer...

Answer 3

I attached the install instructions and owners manual for the Roadmaster Tow Dolly part #RM-2050-1 that you referenced. They are linked on this page under the words, "Featured Help Information."

view full answer...

Answer 4

I went out and took some measurments for you and found that the Replacement Steering Pin and Clip for Roadmaster Tow Dollies #RM-357100-00 is approximately 5-1/2 inches long (4-1/2 inch usable length) by 5/8 inch diameter. I have included a few other…

view full answer...

Answer 5

I spoke with my contact at Roadmaster and he said that on a Roadmaster Tow Dolly Trailer like the #RM-2050-1, the serial number will be located on the tongue of the trailer or on the passenger side, main base, facing forward.

view full answer...

Answer 6

With a tow bar such as #63180 you will have to have the toad lined up straight behind the RV to even attach it to the brackets on the toad. So the process of actually connecting the vehicle to the RV ensures that it is lined up straight. On tow bars…

view full answer...

Answer 7

I may have an option for you but we only carry stabilizer bars for the Roadmaster Tow Dolly RM-2000-1 and RM-2050-1. If you have the former you'll need the Replacement Stabilizer Bar part #RM-921006 or if you have the latter you'll need the…

view full answer...

Answer 8

In regards to the Roadmaster Tow Dolly Ramp Wear Strip and Spacer Plate Replacement Kit part #RM-2000-25, the instructions state to "Apply the supplied lubricant to the top of the replacement deck spacer and the two replacement ramp wear…

view full answer...

Answer 9

Yes, they are made of wood. No, but the Roadmaster Tow Dolly Ramp Wear Strip and Spacer Plate Replacement Kit part #RM-2000-25 aren't an upgrade, they are the same wear plate that would have came with the trailer when purchased new. They are made…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

How Long is Replacement Stabilizer Bar # RM-B001225

Product Page this Question was Asked From

Continue Researching