How to Use Power Drill to Make Raising and Lower Scissor Jacks for Camper Quicker

Question

Question:

I was wondering if I can use a drill such as a impact drill to raise and lower the jacks quicker

asked by: Joe

0

Expert Reply:

Yes, you can use a drill to make raising and lowering the scissor jack set part # JSC-24 a bit quicker. You'll just need the drill adapter part # UF48-979005 too and you'd be set. This basically is a socket attached to a power drill shank. The size socket that comes with this is 3/4 inch.

See review video I attached for this as well.

expert reply by: Jameson C

0

Answer 1

For your 2018 Jayco Melbourne, I recommend the Ultra-Fab Power Twin II Electric Stabilizer part #UF39-941705. This leveling system works with frame rails spaced between 48" to 80" apart.

view full answer...

Answer 2

The Stromberg Carlson Trailer Jack, #JSC-24, does not include any mounting hardware. It can be bolted or welded on to your trailer. If it is being bolted on we recommend grade 5 bolts, with washers and locking nuts.

view full answer...

Answer 3

There is no difference, that is just what the manufacturer decided to label it as. They both do the same job. Both Leveling Scissor Jacks, like part #JSC-24, and Stabilizing Scissor Jacks, like part #TJSCHD-24, are used to keep your RV level and…

view full answer...

Answer 4

The Stromberg Carlson Leveling Scissor Jack Set #JSC-24 will do a really good job of helping to stabilize your boat trailer for the winter and they will be easier to operate than jack stands. It is important to note though that stabilizer scissor…

view full answer...

Answer 5

Yes, you can use a Leveling Scissor Jack Set #JSC-24 to stabilize your Class C motorhome without having to attach them to your frame. Some of the more popular options are the MORryde Hitch Mounted Trailer Stabilizer #MR22AR and Valterra Folding…

view full answer...

Answer 6

The Leveling Scissor Jack Set part #JSC-24 can be mounted on a motorhome yes. In regards to installation, the jack will need to be attached to a part of the frame but there aren't many other mounting restrictions. However, I do recommend you…

view full answer...

Answer 7

Leveling scissor jack set #JSC-24 can support 5000lbs. If you had two sets of these, one on the front of the camper and another on the back of the camper, in addition to the four existing jacks on your camper, you would be able to stabilize and…

view full answer...

Answer 8

From the picture that you sent, it does look like the Replacement Manual Override Crank #BD500203 is a possible fit. The reason I say possible is because I am not sure what the dimensions are in the picture that you supplied. I went out to the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...