Can Bulldog Square Landing Gear Jack # BD182701 Work on 20k Trailer

Question

Question:

we have a exciss trailer live in quarters... gvw is 14000 tgw - 20000 is this jack sufficient? currenct jack is broke and name plate data on the jack is worn off

asked by: Dave

0

Expert Reply:

Landing gear jacks typically support between 25 and 30 percent of the total weight of a trailer. So if your trailer weight up to 20,000 lbs the Bulldog Square Jack # BD182701 that you referenced with it's 12,500 lb capacity would easily be rated high enough. The minimum capacity you'd need is 6,000 lbs.

For more info on the jack check out the review video I attached for it.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 6

The Holland Binkley model 48,000 series jacks are very similar to the Bulldog Square Jack - Drop Leg w/ Spring Return #BD182815 which can utilize the Bulldog Powered-Drive Kit for Single-Speed Jacks w/ 12,000-lb Capacity #BD1824200100. Your current…

view full answer...

Answer 7

Instead of using the Hydraulic Brake Kit #AKFBBRK-35-D which requires using 14"-16" wheels you should use the Dexter Galphorite Free-Backing Hydraulic Trailer Brake Assembly Right #T4423400 and Left #T4423500. These will fit with your…

view full answer...

Answer 8

To determine the location for the front and rear hangers on your tandem axle trailer you will first need to make sure that you have the correct center point for your equalizer hanger. The center point of your equalizer hanger needs to be located…

view full answer...

Answer 9

There sure is; Titan is actually Dexter now, but there is a 6-hole weld-on bracket that you can use with the coupler. The exact parts you need are as follows: - Dexter Bolt-On Coupler for 2 5/16" Ball - Primed - 21K #T4855300 - Demco 6-Hole…

view full answer...

Answer 10

I have a number of dimensions for you of the Buyers Products Heavy-Duty 4" Square Jack w/ Side Pin Drop Leg - Sidewind - 26" Lift - 12K #3370091410H. It has a 4" square tube, an 8" x 8-1/2" foot pad, is 28" tall when it…

view full answer...

Answer 11

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Can Bulldog Square Landing Gear Jack # BD182701 Work on 20k Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching