Will the Pop & Lock Custom Tailgate Lock Work with An Aftermarket Handle on a 2003 Dodge Ram 1500

Question

Question:

I want a locking tailgate and a backup camera that looks OEM. I found your listing for the lock, and it says it works with OEM handle. I found a handle that I want to get, search Master Tailgaters Replacement for Dodge Ram 2002-2008 Chrome Tailgate Handle with Backup Camera, but Im wondering if you all can tell if it will work with this product. Thank you.

asked by: Trevor

0

Expert Reply:

I do have an option for you but the Pop & Lock Custom Tailgate Lock part # PAL8340-PL9510 is designed to work with the factory tailgate handle so there would be no way for me to confirm it will work with the Master Tailgaters Handle you are referring to. However, I have attached a photo for you as well as a video that shows how the above mounts which you can then compare to the handle you want to use to see if they will work together.

If you wanted a backup camera then your best option would be to just add the Hopkins Rear View Camera with Backup Sensors part # HM60195VA which attaches to the licence plate mount.

expert reply by: Conner L

0

click to enlarge

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 3

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 4

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 5

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 6

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

We have an aluminum 7 spoke 14 inch trailer wheel that looks pretty close to the wheel in the picture you sent us, but it's not an exact match. For that wheel you would want the part #AM22329. For a 205/75R14 you can use #AM10234 or tire #AM10229…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...