Is it a Problem that the Lower Brackets of the Air Lift Load Lifter 7500 are Sharp

Question

Question:

Just had the Air Lift 7500 bags installed replaced the 5000s and Im not thrilled with the way the lower brackets have 4 sharp corners on each side that are what sits on the axle tube. Seems like over time this might damage the axle tube and that the design isnt ideal to support the weight of the truck on the air bags. Might need to take them off and grind off that corner, but shouldnt have to do that if they were better designed.

asked by: Mike

1

Helpful Expert Reply:

I would agree that's it's odd the corners are sharp, but we've not had any issues with the # AL57595 installed in trucks like your 2006 Dodge Ram and since the bracket doesn't move on the axle it would not wear it down over time. You would be fine as-is without having to smooth out the brackets.

expert reply by: Jameson C

1

Answer 1

Yes, it is true that most types of 5th wheel to gooseneck adapters will cause stresses on the trailer's frame and in some instances may actually void the warranty on the trailer frame. However, there is one type of 5th wheel to gooseneck…

view full answer...

Answer 2

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Answer 9

The airbags that I recommend for your 2018 Ford F-250 are the Air Lift LoadLifter 5000 Air Helper Springs part #AL57399. These airbags will not interfere with the B&W Turnoverball Underbed Gooseneck Trailer Hitch part #BWGNRK1116 as you can see…

view full answer...

Answer 10

The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 will fit your 2022 Ram 3500 Mega Cab with single rear wheels. This is the extra heavy duty 7,500 lb kit so it is most commonly used on dually trucks, but it will fit single rear wheel models…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

The factory prep package on a 2018 Ram 3500 is pretty apparent so odds are you don't have this if you are unsure. If the indentations for the four outer pucks and center gooseneck hitch ball are present but there are no actual holes in the truck…

view full answer...

Is it a Problem that the Lower Brackets of the Air Lift Load Lifter 7500 are Sharp

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching