Replacement Disc Brake Pads for 2006 MasterCraft Tandem Trailer

Question

Question:

Need brake pads

asked by: Steve T

0

Expert Reply:

From my research it appears MasterCraft specifies Kodiak disc brakes on their tandem boat trailers so you'll just want to confirm the axle rating. Then just review the linked page that displays all Kodiak replacement pads like the part # K225CP that you referenced. Since these pads work for 3500- to 6000-lb brake assemblies they are most likely the ones you need. Each kit includes parts for one axle. We also have upgraded pads # K225CPSS with a stainless steel backing plate for superior corrosion resistance.

expert reply by: Adam R

0

Answer 1

You will need the DeeMaxx Ceramic Brake Pads with Stainless Steel Back Plates #DE98VR to fit the DeeMaxx Disc Brake Kit DBSO-6K-MAXX #DE82FR. We also have the Stainless Steel Caliper #DE58VR if you want to upgrade your caliper.

view full answer...

Answer 2

Yes, you are correct the Kodiak Ceramic Brake Pads with Stainless Steel Backing Plate #K225CPSS will fit your Kodiak Disc Brake Caliper Model 225. For Ceramic Brake Pads without the stainless steel backing plate you will want #K225CP for your model…

view full answer...

Answer 3

To select the correct replacement disc brake pads click the provided link and filter the results by weight capacity and brand.

view full answer...

Answer 4

For a Dexter 3,500 lb trailer axle we have the replacement brake pads of part #K71-623-00 which would work fine on a boat trailer.

view full answer...

Answer 5

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...