Will Lippert Electric Landing Gear # LC333964 Fit 2006 Outback Keystone 29
Question:
Need to replace landing gear... will this one work?
asked by: Nicky
Expert Reply:
Most likely yes as the Lippert Electric Landing Gear Set # LC333964 you referenced is designed to fit the standard fifth wheel trailer mounting locations. The sure way to tell is that if the distance between the mounting brackets (underside of top bracket to top of lower bracket as shown in the diagram) is 17-1/2 inches. If this is the case, the landing gear should fit just fine. If not they can be rewelded as needed. This is by far the most popular setup seen on trailers.
If your frame clamps are instead 20-1/4 inches the Ultra Fab part # UF17-943010 would be a direct replacement.
Products Referenced in This Question
Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 10001 lbs or More
- Electric Jack
- Landing Gear
- 38 Inch Lift
- Weld-On
- 2 Jacks
- Ultra-Fab Products
more information >
Product Page this Question was Asked From
Lippert Electric Landing Gear Set - Weld On - 37" Lift - 6,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Electric Jack
- Landing Gear
- 37 Inch Lift
- Weld-On
- 2 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Search Results: fender skirt
- Shop: Lippert Manual Landing Gear Set with Handle - Weld On - 37" Lift - 6,000 lbs
- Shop: Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies
- Shop: Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Replacement Aluminum Gearbox for Stromberg Carlson Landing Gear
- Shop: Replacement Follow Leg for Keystone Montana 5th Wheel Landing Gear
- Video: etrailer Landing Gear Set Review
- Search Results: landing gear
- Q&A: Will Lippert Landing Gear Fit Trailer with Weld Stop Brackets of Different Dimensions
- Q&A: Replacement Landing Gear for 2006 34 ft Keystone Montana
- Q&A: How Do Tabs on Lippert LC178653 Landing Gear Leg Fit in Clips Welded onto 5th Wheel Frame
- Q&A: Replacement for Ventura Landing Gear on 2008 Keystone Cougar 281BHS
- Q&A: Dimensions of Lippert Landing Gear LC333966
- Q&A: Replacing Landing Gear for 2003 Keystone Cougar Fifth Wheel
- Shop: Trailer Hitch
- Search Results: trailer jack
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Video: etrailer Camper Jack - Landing Gear - RVLG-8000 Review
- Article: Trailer Tire Sizing
- Search Results: jack
- Video: Review of Ultra-Fab Products Camper Jacks - Landing Gear - UF17-943010
- Shop: Suspension Enhancement
- Article: Most Popular Wheel Bearings
- Search Results: lc142178
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Fifth Wheel Hitch