Replacement Motor for Lippert Tread Lite RV Steps

Question

Question:

Do you happen to sell just the motor for these steps? I have a 2018 Coachmen Mirada 35BH and my steps stopped functioning and it is now in the locked out position.

asked by: Derek

0

Expert Reply:

The replacement motor you need is the # LC183058 for the Lippert Tread Lite steps # LC353543 that you referenced.

It could be the sensors on the door of your RV that's either failed or fallen off. You might check there to verify that the magnets are there and working properly. These sensors basically are what tells the steps your door is open or closed and needs to retract or extend. Since the step is stuck in the out position and the magnets being near each other is what tells the steps to retract it's very possible your magnets aren't getting close to each other for some reason.

expert reply by: Jameson C

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The factory prep package on a 2018 Ram 3500 is pretty apparent so odds are you don't have this if you are unsure. If the indentations for the four outer pucks and center gooseneck hitch ball are present but there are no actual holes in the truck…

view full answer...

Answer 6

Hi Rick, The Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #GY86GR could potentially work but you'll need the correct gooseneck to fifth wheel hitch adapter or you'll want to switch to a gooseneck pin box like #GY98GR. The #GY86GR is designed…

view full answer...

Answer 7

Hey Mark, since we know your Brinkley Z3100 has the Rhino style pin box, the correct Gen-Y fifth wheel to gooseneck adapter is the part #GY98GR which comes with the auto latch you mentioned wanting as well!

view full answer...

Answer 8

The factory prep package or pucks are not the same between Ram, GM and Ford. The spacing is all different which means you cannot use a 5th wheel hitch for Ram pucks on a GM with pucks. Take the Curt A25 5th Wheel Trailer Hitch for example which is…

view full answer...

Answer 9

Hey Bob, Roof rack systems are typically only rated up to 165lbs because that's typically above the capacity of the vehicle's roof. More recently all manufacturers are switching to removing the capacity from the listing and telling consumers…

view full answer...

Answer 10

The best way to test this out is by applying 12V power to the motor directly so you can see if it operates correctly outside of the control module (see attached). If everything works properly when you've bypassed the control module then…

view full answer...

Answer 11

For frame mounted camper tie downs that are a confirmed fit for your 2016 Dodge Ram 3500 Dually we have the TorkLift camper tie downs part numbers #TLD2131 for the front and part #TLD3109 for the rear.

view full answer...

Replacement Motor for Lippert Tread Lite RV Steps

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching