Is Loctite Suggested When Installing Trailer Hitch Receiver

Question

Question:

Just about to install this received hitch that was ordered from you. Do you suggest using loctite on the bolts. Nothing is mentioned in the instructions

asked by: David P

0

Expert Reply:

When installing a trailer hitch receiver like # 75081 we do not suggest using Loctite on the bolts and nuts because the manufacturer doesn't. It isn't a bad idea in most cases to use # LT37643 because it will keep the hardware tight. The only situation where I wouldn't recommend it is when you have weld nuts in the frame, which isn't an issue with this hitch.

expert reply by: Jason S

0

Answer 1

No, you will not have to cut, drill or modify the vehicle in any way when installing the Curt #C26VV on a 2024 Toyota Grand Highlander. This is actually about as easy of a hitch installation as you will see. You will just lift the hitch into place,…

view full answer...

Answer 2

Below the bumper. The Curt Trailer Hitch item #C26VV mounts to the bottom of your 2024 Toyota Grand Highlander's frame and extends out below the bumper and trim. This installation method requires no cutting of your trim or fascia. The Curt item…

view full answer...

Answer 3

Yes, it does. I just checked with Curt and their item #C26VV hitch does indeed fit the Hybrid Max model of the 2024 Toyota Grand Highlander. This hitch is custom fit and bolts to your Toyota with included hardware. I have linked the installation…

view full answer...

Answer 4

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 5

It honestly could not be easier to install the Curt hitch on your 2024 Toyota Grand Highlander, and there is no drilling needed. All you have to do is lift the hitch up and bolt it on with the supplied hardware and you're finished. I verified for…

view full answer...

Answer 6

In most cases Loctite is not required when installing a trailer hitch, but it would not be a bad idea. I suggest using the Loctite Blue Stick Threadlocker, #LT37643, which will provide a secure grip and protect against water and grime.

view full answer...

Answer 7

I looked up the instructions for the Draw-Tite hitch, part #75270, and the torque specification for the 6 M12 bolts is 68 Lb.-Ft. I have added a link to the instructions below so that you can review them. The torque rating is just above the small…

view full answer...

Answer 8

In some cases trailer lighting will ground through the hitch ball but that's typically only if the actual ground circuit is insufficient. This is not an ideal setup. It needs to ground through the wiring of the trailer harness. You can test this…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 12

I have attached a picture below of the Curt Hitch item #C26VV installed on a 2024 Toyota Grand Highlander. I really like this hitch because the crosstube installs behind the rear bumper leaving only the 2" receiver exposed. The Curt Hitch item…

view full answer...