What Torque Rating Should the Bolts Be Tightened to on Draw-Tite Hitch 75270

Question

Question:

How much torque do i need to apply when i install the hitch. I dont think its in hte installtion instruction paper. 2005 Honda Odyssey

asked by: Ruben V

0

Expert Reply:

I looked up the instructions for the Draw-Tite hitch, part # 75270, and the torque specification for the 6 M12 bolts is 68 Lb.-Ft. I have added a link to the instructions below so that you can review them. The torque rating is just above the small print on the first page.

expert reply by: Patrick B

0

Answer 1

The custom fit receivers we offer do come with the appropriately sized/pitched bolts. If anything we get phone calls where the 1.25 bolts seem too big. If you have any issues trying to get the bolts into the existing weld nuts on the van we recommend…

view full answer...

Answer 2

For the Draw-Tite trailer hitch, #75270, or any of the trailer hitches we carry, the torque specifications can be found after the last step in the installation instructions that are linked on the page. Because the design of a hitch could change or…

view full answer...

Answer 3

We don't post the torque specs for the hitches we carry as they are subject to change by the manufacturer and since we link the install instructions for all of the hitches directly from the manufacturer if they were to ever change our linked…

view full answer...

Answer 4

The Curt #CU94FR vehicle wiring harness plugs into the same factory connector located under your 2022 Hyundai Palisade and will have a 4-way flat connector. This connector will allow for you to connect to most small trailers as well as use Auxiliary…

view full answer...

Answer 5

In most cases Loctite is not required when installing a trailer hitch, but it would not be a bad idea. I suggest using the Loctite Blue Stick Threadlocker, #LT37643, which will provide a secure grip and protect against water and grime.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

When installing a trailer hitch receiver like #75081 we do not suggest using Loctite on the bolts and nuts because the manufacturer doesn't. It isn't a bad idea in most cases to use #LT37643 because it will keep the hardware tight. The only…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...