Is Loctite Required When Installing a Trailer Hitch

Question

Question:

Do you suggest using locktite on the bolts that connect a hitch to the frame of the vehicle?

asked by: Brian D

0

Expert Reply:

In most cases Loctite is not required when installing a trailer hitch, but it would not be a bad idea. I suggest using the Loctite Blue Stick Threadlocker, # LT37643, which will provide a secure grip and protect against water and grime.

expert reply by: John H

0

Answer 1

To answer the last question first you could attach some quick links to the safety chain loops on Curt trailer hitch #C15410 so that they are compatible with smaller hooks. We have different size quick links and S-hooks depending on your needs and I…

view full answer...

Answer 2

Using Loctite when installing a trailer hitch is not required but it can certainly be used to create an even stronger bond. Blue Loctite like the Blue Stick #LT37643 is plenty sufficient for this application. As long as the hardware for your hitch…

view full answer...

Answer 3

If your 2022 Kia Telluride does not have any of the wiring for adding a tow package you will need the Upgraded Heavy Duty ModuLite Circuit Protected Vehicle Wiring Harness #C59496 to tie into the tail light wiring for a 4-way flat trailer…

view full answer...

Answer 4

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 5

Most likely you had some corrosion or dirt in the threads of the weldnuts of your 2015 Acura MDX which was causing the bolts to not be able to thread all the way in. This is a pretty common issue which affects the install of trailer hitch hardware.…

view full answer...

Answer 6

To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel…

view full answer...

Answer 7

The only available hitches for a 2010 Toyota Prius have 1-1/4" receiver openings and are Class I rated. Class I racks are limited to carrying two bikes, though there are some that have an available adapter that allow bikes to be used with…

view full answer...

Answer 8

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at…

view full answer...

Answer 9

The Tow Ready 2 Inch Hitch Ball, part #63845, you have referenced needs to be torqued to 250 foot pounds. It is recommended to frequently check that the ball is tightened to these specifications. If you are meaning the mounting bolts that are used…

view full answer...

Answer 10

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a…

view full answer...

Answer 11

The Master Lock Hitch Receiver and Coupler Latch Lock Set - Padlock - 1-1/4" and 2" Hitches #2848DAT has replacement keys if you know the key number using #MLK1. If you do not know your key number, unfortunately there is no way to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Is Loctite Required When Installing a Trailer Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching