How Does Exhaust Ventilator # PLR23 Mount On Side of Trailer

Question

Question:

I am interested if this 12 v powered vent can be installed vertically. Ie would rain get in. Also how big of a hole do you need.

asked by: Curt E

0

Expert Reply:

The Exhaust Ventilator # PLR23 that you referenced is designed to mount horizontally and is designed to be mated with a 7-1/4 inch diameter butterfly vent on the interior side of the trailer with the part # PLR24-002 which comes with a gasket.

expert reply by: Jameson C

0

Answer 1

The only differences between the vents is that part #PLR24-004 comes with a rubber gasket and part #371800 does not. The mounting holes are also positioned a little differently. They are both 7-1/4" in diameter and made of a polished aluminum.…

view full answer...

Answer 2

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

How Does Exhaust Ventilator # PLR23 Mount On Side of Trailer

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching