Replacement Bow Roller with Bell Ends for a 2011 Skeeter SX200 Boat Trailer

Question

Question:

My EZloader trailer VIN begins with 1L8. 2011Skeeter SX200. Will this blue roller fit my trailer?

asked by: Hector

1

Helpful Expert Reply:

It would appear from the photo you attached that the distance between your mounting bracket is 4" wide which means the correct blue roller assembly for you is the Bow Roller Assembly w/ Bells for 4" Wide Bracket part # YR450B-400B. This assembly will be a nice upgrade for your trailer as the thermal-plasticized rubber will help to absorb shock without marking the boat up and the included bell ends will ensure there is no contact with the mounting bracket.

I have attached a review video for you as well.

expert reply by: Conner L

1

click to enlarge

Answer 1

A TPR roller like the #YR500YW-6P is going to be better than PVC. PVC is a cheaper product. TPR has the properties and performance of both PVC and rubber while having a higher tensile strength so it is going to be the most durable. I don't…

view full answer...

Answer 2

It's very possible the pads you mentioned are the correct ones for your trailer but I'd need more info from you. The trailer number you mentioned does not reference anything online so I'd need you to get me brand of your disc…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 8

EZ Lube axles like the item #T3584F-EZ-8974 come from the factory with just a little bit of grease in the bearings. The first time you use the EZ Lube feature to fill the axle, it will take a lot of grease. You will probably use 3/4 to a full tube…

view full answer...

Answer 9

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 10

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any…

view full answer...