Available Sizes of Spindle Jam Nuts

Question

Question:

Looking for a 22x1.25 axle jam nuts

asked by: Sammy C

0

Expert Reply:

We offer a couple of spindle jam nuts, part # 6-191 that you referenced which has an inner diameter of 1-inch, and part # 6-96 which has an inner diameter of 1-1/2-inches. We do not offer any with an inner diameter of 1-1/4-inches.

expert reply by: Adam R

0

Answer 1

Your 2014 F-250 may or may not require an adapter. HydraStar states only the (2007 - 2008) Ford F-250 requires it however, in some late model trucks it can be hit or miss. If the factory brake controller isn't putting out enough voltage then it…

view full answer...

Answer 2

The adapter part #K22590A that you referenced is designed to fit the fitting size of Kodiak brake systems. This has a 90-degree bend and measures 1/8" NPT on one end and 3/16" FIF on the other end.

view full answer...

Answer 3

Yes, the correct Replacement Bleed Port for Kodiak 225 Disc Brake Calipers, like #KDBC225DAC is part #KBPBB, which has the correct 1/4"-28 bleed screw and 1/8" adapter fitting. Just in case, the correct replacement silicone dust boot is…

view full answer...

Answer 4

We have the Kodiak brake line part #bh-3mfs-15 which is 15 feet long and has the 3/16 inch male fitting on both ends. Then for a fitting adapter we have the part #K22590A which goes from 3/16 inch to 1/8 inch.

view full answer...

Answer 5

Sounds like you are looking for the adapter part #K22590A. This adapter port features a 90-degree bend and measures 1/8" NPT on one end and 3/16" FIF on the other end.

view full answer...

Answer 6

The Replacement Nut Retainer for 6-191 Jam Nut #6-190 fits Replacement Trailer Spindle Jam Nut #6-191 which fits 2,000 lb to 8,000 lb axles with E-Z Lube spindles. That means it will fit your 5,200 lb axle if it has an E-Z Lube spindle.

view full answer...

Answer 7

The thread diameter of spindle jam nut #6-191 is 1 inch. If you do need a 3/4 inch then this nut will not work, though it is for EZ lube spindles that have the grease zerk at the end. We do not have a 3/4 inch jam nut. The closest match is a 7/8 inch…

view full answer...

Answer 8

The TruRyde Replacement D Tang Spindle Washer #5-101 that you referenced has a 1-inch inner diameter to fit on 1-inch diameter spindles. All such items that we offer share this same 1-inch inner diameter, such as parts #5-23 and #5-57. The points on…

view full answer...

Answer 9

For castle nut #165931, for a D washer use part #5-23 or round washer use part #SW1000. These are both for 1 inch spindles but are compatible with the 7/8 inch castle nut assemblies. You can also use the Replacement Spindle Washer - Tang Type for E-Z…

view full answer...

Answer 10

Thanks for the picture of the plate on your axle. Based on that I was able to determine you have a Dexter 3,500 lb axle and the correct bearing kit is the #BK2-100 that you referenced. For additional tang washers you'd need the part #5-101.

view full answer...

Answer 11

Yes, you can simply use the nut retainer part #6-191 on your spindle nut instead of the tang washer setup and it would work just fine. The EZ lube fitting would not be an issue at all.

view full answer...

Answer 12

Hubs that use #L44649 inner and outer bearings are idler type hubs like #AKIHUB-440-2-2K. The correct matching race is indeed part #L44610. We offer these as individual parts but we also offer a complete bearing kit #BK1-150 that includes bearings,…

view full answer...

Available Sizes of Spindle Jam Nuts

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching