Parts Needed to Install 7-Way in 2001 Ford Expedition with Factory 4-Flat

Question

Question:

I have a 2001 Ford expedition xlt 2wd and it already has a 4 way connector going into the factory harness but I need a 7 way and I noticed that this kit looks like it has 2 unused wires at the trailer end of the 4 way is this so you can install a 7way? If so what wire would I be missing to complete the 7 way plug?

asked by: Nathan S

0

Expert Reply:

Since your 2001 Ford Expedition already has a factory 4-flat you will need the Adapter 4-Pole to 7-Pole # 37185.

Your '01 Expedition should have the factory wiring already run to the connector on the frame rail so you will need to splice in the adapter; for extra wire you can use # 12-1-1 along with butt connectors # 05732-2.

I have added a link to a help article about installing a brake controller in a Ford like your '01 Expedition which I strongly recommend reading. It will explain how to find and wire the Adapter 4-Pole to 7-Pole # 37185 with a factory installed 4-way.

expert reply by: Kyle S

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 8

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 9

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 10

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 11

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 12

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Parts Needed to Install 7-Way in 2001 Ford Expedition with Factory 4-Flat

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching