Recommended Trailer Hitch for a 2014 Chevrolet Silverado 1500

Question

Question:

On BandW Website it says that this trailer receiver HDRH25217 will fit 2008-2018 1500 Silverado models. But, on yalls site it says it wont. Will this still fit for a 2014 Silverado?

asked by: Brooks

0

Expert Reply:

Yes, the B&W Heavy-Duty Trailer Hitch Receiver part # BWHDRH25217 will fit your 2014 Chevrolet Silverado 1500. I was able to confirm with my contact at B&W and the install instructions that this trailer hitch will fit a 2008-2018 Chevrolet/GMC 1500 light duty truck with the factory bumper.

I have attached an install video of this trailer hitch for you as well.

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 8

Yes, you can! So long as our Kenda Loadstar 5.30-12 Bias Trailer Tire with 12" White Wheel item #AM30820 is the same size and bolt pattern as what's on your Ironton trailer it can be used not only as a spare but also on your trailer with the…

view full answer...

Answer 9

Hey Sylvia, the diameter of the lock core side of the B and W Coupler Lock part #BW23FR is 1 inch.

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...