Mounting Hole Spacing on Curt Trailer Hitch Receiver # C12923

Question

Question:

Whats the measurement between the two mounting holes?

asked by: Harold R

0

Expert Reply:

The mounting holes on the Curt Trailer Hitch Receiver # C12923 are spaced apart exactly 4.4 inches front to back, on center.

Horizontally left to right the mounting holes can be spaced apart as short as 31-1/2 inches to as long as 41-1/2 inches depending on how you adjust the crosstube. This Class II hitch features a towing weight capacity of 3,500 pounds and a tongue weight limit of 350 pounds. I have attached the written installation instructions that you can check out as well.

expert reply by: Chris R

0

click to enlarge

Answer 1

I went out to our warehouse and measured the Curt Front Mount Trailer Hitch Receiver part #31026 for you. The distance between the bolt holes on center is about 37" left to right and 4-1/4" front to back. I have attached a photo…

view full answer...

Answer 2

We have not yet had a chance to test fit the Curt Front Mount Trailer Hitch part #C31013 on a vehicle specifically a Toyota Tacoma. So I would not be able to tell you exactly how much ground clearance is lost. However, I went out the warehouse and…

view full answer...

Answer 3

I spoke with my contact at Curt and he put together a chart that has all of the dimensions of the hitches you referenced.

view full answer...

Answer 4

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the…

view full answer...

Answer 5

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of…

view full answer...

Answer 6

The 2015 Jeep Patriot with either 2.0L or 2.4L engine does have a towing capacity of 1000-lbs; the 2.4L models with the Trailer Tow Prep Package (AHC) or the Freedom Drive II Off Road Package (AWL) can tow up to 2000-lbs trailer weight. You can see…

view full answer...

Answer 7

I spoke with my contact at Curt and I got the measurements between the bolt holes for you. I made a picture that shows the following dimensions: Side to side on center the holes are 40 inches apart. From the hole closes to the receiver to the next…

view full answer...

Answer 8

The Curt Trailer Hitch Receiver - Multi Fit - Class III - 2" #C13900 measures 4-3/8 inches from the frame mounting point to top of crossbar. It measures 6-7/8 inches from the frame to the bottom of the crossbar and top of the receiver…

view full answer...

Answer 9

According to the linked installation instructions the Curt Trailer Hitch Receiver - Multi Fit #C13900 is compatible with your 2005 Chevy Tahoe LT. You will have to drill out the holes marked A, C, and D on both sides for this application.

view full answer...

Answer 10

I had our warehouse measure each of the front mount trailer hitch receivers you mentioned, and the dimensions are as follows. The Curt #31408 measures 32-3/4" long x 8-3/4" wide, the Draw-Tite #65080 measures 36-3/4" long…

view full answer...

Answer 11

I was able to get the measurements you were looking for of the Draw-Tite front mount hitch that fits your 2020 Toyota Tundra, which is the following: - Draw-Tite Front Mount Trailer Hitch Receiver #65080 The hitch is similar to the Curt #31198 in…

view full answer...

Answer 12

I checked with Curt and they told me that the overall width of the Curt front hitch #C31013 is 32.50 inches and the center to center hole dimension is 30 inches.

view full answer...

Mounting Hole Spacing on Curt Trailer Hitch Receiver # C12923

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching