Could B&W Offset Adapter be Used in Flat Bed Truck Gooseneck Hitch

Question

Question:

Can this offset ball work with the built in BandW in a flatbed?

asked by: JR

0

Expert Reply:

If you had the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks # BWGNRK1500 installed in your flat bed truck you could pretty easily use the 4 inch offset part # BWGNXA4085.

expert reply by: Jameson C

0

Answer 1

Congrats on the new hobby! A Reese Goose Box like item #RP85FR doesn't do much to help you with clearance and you will want all the help you can get with a short bed truck. You have two options to get more clearance when turning or backing in…

view full answer...

Answer 2

The Ranch Hitch Universal 5th Wheel to Gooseneck Coupler Adapter #AM3139 can potentially work with a recessed gooseneck ball on a flat bed truck, but it's going to depend on just how much the ball is recessed and how much space you have around…

view full answer...

Answer 3

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 4

When asked for our recommendation about trucks that are towing fifth wheel or gooseneck trailers, most of the time we will recommend 1-ton trucks with an 8-ft bed and a diesel engine. The truck I recommend is the Ram 3500 Dually Tradesman with a 6.7…

view full answer...

Answer 5

There should be two fuses in the electrical panel under the hood of your Dodge Pickup for the trailer wiring. Check those again and you may find that is the problem. If all of the fuses are good then I would use a circuit tester, item #PTW2993, to…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Could B&W Offset Adapter be Used in Flat Bed Truck Gooseneck Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching