Does Installation of CURT Front Hitch # C31022 on 2003 Jeep Liberty Require Drilling

Question

Question:

Does it require drilling to install to a jeep liberty 2003 ?

asked by: Carlos D

0

Expert Reply:

The installation of CURT Front Hitch, part # C31022, to your 2003 Jeep Liberty, will require a couple of holes to be drilled on the vehicles frame. If you have a front air dam it will have to be permanently removed from the vehicle.

I am including a link to the installation instructions of the CURT hitch that will show you where the holes are to be drilled.

expert reply by: Jeff D

0

Answer 1

As shown in the provided photo, the receiver tube of the Curt #C31022 front mounted receiver will be located just under the front bumper and would be a good fit for your 2005 Jeep Liberty. If you click the provided link, you an see the installation…

view full answer...

Answer 2

I checked with Curt and the Curt Front Mount Trailer Hitch part #C31022 is a fit for all models of the 2006 Jeep Liberty so yes, it will fit models with the CRD engine.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

The EcoHitch Hidden Trailer Hitch Receiver #EH35VR may interfere with the Hands-free Liftgate sensor like all of the other hitches. Typically this means you will need to place your foot on either side of the receiver tube in order to activate the…

view full answer...