Axle Flip Kit for a 1,000 Lb to 2,000 Lb Trailer Axle 1-3/4 Inch Diameter
Question:
I want to replace my 2 leaf springs with 4 leaf springs. Can I purchase 1 7/8inch x 6inch ubolts to handle the additional thickness of the springs? Also, I would like to switch the axle to ride below the springs Is there a kit available to enable the conversion? you
asked by: Jerry
Helpful Expert Reply:
I have a solution that will allow you to flip your axle but there is not an all-inclusive kit for your axle size so we will need to piece together one. I assume you have a 1-3/4" diameter axle (1,000 lb - 2,000 lb) so that means you will need the U-Bolt Kit part # APUBR-10 and the Spring Seat part # TRSS175 (2). These u-bolts are 4-1/4" which is the longest we have for this width. However, I would highly doubt that you will require a 6" long u-bolt as most leaf springs are only 3/8" thick. The 4-1/4" should have just enough for what you need but if not a trip to your local hardware store should warrant better results.
Products Referenced in This Question
Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Trailer Suspension Parts
- Spring Seats
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Round Axle - 1-3/4 Inch
- TruRyde
more information >
Product Page this Question was Asked From
U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts
- Trailer Suspension Parts
- U-Bolt Kits
- Camper
- Car Hauler
- Utility Trailer
- 2000 lbs
- Round Axle - 1-3/4 Inch
- 3/8 Inch Diameter
- 4-1/4 Inch Long
- Dexter
more information >
Continue Researching
- Shop: U-Bolt Kit for Mounting 2,000-lb, Round Trailer Axles - 4-1/4" Long U-Bolts
- Shop: Spring Seat for Typical 2,000-lb, Round Trailer Axles with 1-3/4" Diameter - Qty 1
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Video: Dexter Trailer Springs Over-Under Conversion Kit Installation K71-384-00
- Search Results: 13" tire
- Shop: Kenda Karrier ST145/R12 Radial Trailer Tire with 12" Black Mod Wheel - 5 on 4-1/2 - LR D
- Shop: Dexter Trailer Springs Over-Under Conversion Kit
- Shop: Deka Jacketed 4-Wire - 14 Gauge - Per Foot
- Shop: Kenda Karrier ST175/80R13 Radial Trailer Tire with 13" Black Mod Wheel - 5 on 4-1/2 - LR D
- Video: TruRyde Trailer Suspension TRSS175 Review
- Video: Redline Round Trailer Axle U-Bolt Mounting Kit Review
- Search Results: wheel bearings
- Search Results: dexter lift kit
- Search Results: 5 lug spare tire mount
- Search Results: e82gr
- Q&A: Does Over Under Kit for 1-3/4 inch Axle Require Welding
- Q&A: Hubs for 13 Inch Tire with 5-1/2 Hub Flange Diameter
- Q&A: Replacement 61 Inch Axle With 2 Inch Diameter
- Q&A: What Information is Needed to Replace Trailer Axle
- Video: Kenda Tires and Wheels - Tire with Wheel - AM32131 Review
- Video: Dexter Axle Trailer Suspension - Leaf Spring Suspension - K71-384-00 Review
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-545-2-G-EZ-1K Review
- Search Results: e99sr
- Article: Snow Tire Chain Overview: How to Buy the Right Tire Chains
- Q&A: Determining Correct Replacement Bearing
- Q&A: Can 12 Inch Trailer Tires and Wheels be Replaced with 13 Inch
- Q&A: What is the Best Grease for Trailer Bearings
- Shop: Tire Chains
- Article: Printable Trailer Bolt Hole Pattern Template
- Video: Redline Trailer Suspension - Leaf Spring Suspension - APS3SE Review
Nicholas K.
9/7/2020
Spring seat TRSS175 shows the outside channel dimension of 1-7/8" but the APUBR-10 bolts have a 1-3/4" gap. If the bolt pattern for the plate is square, then wouldn't the recommended seat be too big? Is the bolt pattern not square? The TRSS175 seat seems to be the recommended seat for the APUBR-10 kit but the specs shown have me a little concerned about compatibility. Thank you.