Will Curt Q24 Fifth-Wheel Hitch Head fit Slider Base for 2018 Ford F-350 Super Duty with Puck System

Question

Question:

I have Curt Q24 # 16047 that was for a Ram factory puck system long bed see attached picture. I just bought a 2018 Ford F-350 shortbed with puck system. Will the head of my present hitch attach to this slider component listed here? Thank you

asked by: Matt B

1

Helpful Expert Reply:

Yes, the head unit of your Curt Q24 will fit the Curt 5th Wheel Round Tube Slider for Ford Super Duty Towing Prep Package # C16020, which fits directly in the puck system of your 2018 Ford F-350 Super Duty.

expert reply by: Kyle S

1

click to enlarge

Answer 1

The height setting you'll need to use when installing the Curt A16 head part #C16520 that you referenced is going to be based on what your trailer needs to sit level. The height of the head is adjustable as well as how the pin box attaches to the…

view full answer...

Answer 2

I do have third brake light options for your 2019 Ford F-250 although I am not exactly sure what you mean by interphase. The third brake light cameras available for the 2019 F-250 Super Duty are compatible with what specific monitor have from the…

view full answer...

Answer 3

The pressure in the airbag of the #UF35-946215 Trailair Pin Box can range from 20 to 120 psi depending on your situation. Once the pin box is installed, hitch the trailer to the tow vehicle on level ground. There is a sticker on the front of the…

view full answer...

Answer 4

According to Lippert there are many factors that can effect air pressure such as the size of the air spring in diameter and height, the pin weight of the trailer, the mechanics of each individual hitch, altitude and air temperature. Lippert has…

view full answer...

Answer 5

If you check out the sticker or plate on the pin box of your trailer currently there will be a model number listed that will help us identify what pin box you have and then from there pick out the correct Goose Box. If not there is a way you can…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 10

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 11

The safe GVWR rating is 80-85% of total weight capacity to allow for any additional weight added to the trailer. So for a 16k pin box you'd be looking at 12,800lbs - 13,600lbs as a safe weight. I looked up your current pin box with the LCI Number…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...