Will Trailer Hub and Drum Assembly # AKHD-655-35-EZ-K Fit Lippert Axle

Question

Question:

Will this fit a lippert axle

asked by: Jeff G

0

Expert Reply:

Yes, the Trailer Hub and Drum Assembly # AKHD-655-35-EZ-K that you referenced will fit a 3,500 lb Lippert trailer axle.

expert reply by: Jameson C

0

Answer 1

The correct hubs for the 4400 Lb Lippert Axle NV178936 are 3,500 lb hubs as confirmed by Lippert. If you need to replace the hubs, I recommend Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 6 on 5-1/2 - Pre-Greased part…

view full answer...

Answer 2

If the trailer wheel size you have is between 14-1/2 inches in diameter and 16-1/2 inches in diameter the trailer hub #AKHD-655-35-EZ-K that you referenced will fit but if you have a different size wheel this won't work.

view full answer...

Answer 3

The Dexter 3,700 Lb Axle uses an L68149 inner bearing and a L44649 outer bearing so yes, you can get these bearings with a 6 on 5-1/2" bolt pattern. I am not sure if you're after a hub or hub/drum so I have attached our complete selection…

view full answer...

Answer 4

The hub you describe is a 3500 lb 10 inch hub/drum with a 6 on 5-1/2 inch bolt pattern which uses an L44649 outer and an L68149 inner wheel bearing and a 58846 grease seal. For a replacement, I'd recommend the #AKHD-655-35-EZ-K hub/drum. The…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Will Trailer Hub and Drum Assembly # AKHD-655-35-EZ-K Fit Lippert Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching