Replacement Shock Recommendation for UWS Tool Box

Question

Question:

Need to replace shock that holds up the lid on UWS toolbox. Purchased DeeZee replacement shock. #DZ TBSHOCK1. How do I turn the shock to install as both holes face the same but on the box the holes face different directions?

asked by: Robert

0

Expert Reply:

Since you have a UWS tool box the only solution we have for a replacement shock/lift cylinder is the part # UWSLIFTCYLIND. We can't recommend a way to convert a DeeZee shock to fit a UWS tool box like you have.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I contacted our representative and she informed me that the Replacement Lift Cylinder for UWS Toolboxes, part #UWSLIFTCYLIND, mounts to a ball stud on the toolbox. The replacement lift cylinder snaps or pops on to the ball stud and does not use a tab…

view full answer...

Answer 2

In regards to a UWS Truck Bed Toolbox, if the box is locked and there is no key then you have two options. If you know the key number (it may be stamped onto the lock/latch) then you can order a replacement key like the Replacement Key for UWS…

view full answer...

Answer 3

The UWS Replacement Lift Cylinder #UWSLIFTCYLIND is intended specifically for UWS tool boxes with heavy-duty gas lifts. It uses ball socket attachments at both ends as shown in the linked photo. I checked on the Stabilus struts and they appear to use…

view full answer...

Answer 4

To remove the current gas strut on your UWS toolbox you will simply need to take a flathead screwdriver and pop the clip on either head. This will allow you to pull the strut right off. Once the strut is removed you just have to push the ends of the…

view full answer...

Answer 5

Easiest way would be to start with the brand of tool box you have. If it's a UWS we have the part #UWSLIFTCYLIND which will fit it. But if it's a different brand we wouldn't be able to help.

view full answer...

Answer 6

On your UWS toolbox the number for the replacement key you need is printed on the lock cylinder. For example, the part #KEYCH509 is a replacement key made specifically for the UWS Toolboxes that use key code 509. This is the correct replacement key…

view full answer...

Answer 7

Hey Tim! Yes, the Rhino-Rack Ski and Fishing Rod Carrier #RR572 will fit the older Thule square crossbars. While this kit does come with T-Slot hardware, it also has the clamps which is what you'll use for the square crossbars.

view full answer...

Answer 8

I spoke with my contact at UWS and they said that the UWS Replacement Lift Cylinder, part #UWSLIFTCYLIND, will fit all of the UWS toolboxes. The name on the lifts could change if they switch to a different supplier.

view full answer...

Answer 9

We offer a replacement heavy-duty gas strut with a 10-inch dimension between its ball/socket mounts, part #UWSLIFTCYLIND from UWS which is the item you referenced. This item has a weight capacity of 45-lbs. I could not find a cross reference for the…

view full answer...

Answer 10

The Replacement Lift Cylinder for UWS toolboxes, part #UWSLIFTCYLIND measures 7 inches in length when fully retracted, and 11 inches long when fully extended.

view full answer...

Answer 11

The best solution we have is the Kodiak Disc Brake Kit - 11.35" Rotor - #120 Spindle - 12K - ALKO #K2HR12A11-120DW which is designed for your 12k ALKO brake setup. The Dexter rotor you mentioned would not fit and we do not have any rotors by…

view full answer...

Replacement Shock Recommendation for UWS Tool Box

Product Page this Question was Asked From

Continue Researching