Bearing Kit for Stinger Folding Motorcycle Trailer with 3,500 Pound Axles and Sure-Lube System

Question

Question:

Will this bearing kit work with a Stingerinch folding motorcycle trailer? Axles are: • 3500 lb axle with Sure-Lube® Bearings

asked by: Tim H

1

Helpful Expert Reply:

I contacted Stinger Trailers and was able to verify that the Bearing Kit # BK2-100 you referenced is exactly what you need to replace the bearings and seal for the hubs on your folding motorcycle trailer. The Sure-Lube system on the trailer features a drilled grease zerk on the spindle that allows for easy maintenance but the bearings and seal themselves are the standard size and type for 3,500 pound axles.

I have attached an installation video that you might also find helpful.

expert reply by: Chris R

1

Aristarchus O.

3/6/2024

Hi Folks, Do you carry the spindles for this trailer? I need to replace both spindles as the bearings and lubrication were not properly maintained. Thanks. Pat

Reply

Chris R.

3/6/2024

@AristarchusO Hi! It's not necessarily a direct replacement for that specific trailer, but if all those bearings listed above are correct, the #84 Spindle # TRU74FR is exactly what you would need.

Reply

Aristarchus O.

3/20/2024

@ChrisR Thanks Chris, these look to be 4" drop, same flange weld on, with a 4 bolt plate, do you carry those?

Reply

Jesse M.

4/4/2024

@AristarchusO That we do! That is going to be part # TRU87FR.

Reply

Answer 1

The Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW350D does not come with the bearings installed. You can use something like a rubber mallet or a block of wood and hammer to tap them into place until they are flush.

view full answer...

Answer 2

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 3

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Answer 4

From the center of the mounting bracket (Pivot point) to the bottom of the wheels of the Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels - Sidewind - 7" Lift - 770 lbs - Zinc #ORJW350D is 9-1/2" with the jack full retracted, and is…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 10

From the ground to the middle of the mounting bracket for the Extreme Off-Road Swing-Up Jack w/ Dual Wheels #ORJW500D measures 710mm (27.95") when you have it set at the highest setting. This jack gives us the ability to extend the leg using the…

view full answer...

Answer 11

Waylon, it does look like the Dexstar Steel Mini Mod Trailer Wheel #AM20539 is the same thing as the Dexstar 17-233 wheels you're referring too. These are silver wheels with a 6 on 5 1/2 bolt pattern, a 0 offset, and are made in the USA.

view full answer...

Answer 12

The Extreme Off-Road Swing-Up Trailer Jack part #ORJW350D would be the best option for an InTech Flyer Pursue Travel Trailer. The weight capacity of said jack is more in-line with the tongue weight of the trailer.

view full answer...

Bearing Kit for Stinger Folding Motorcycle Trailer with 3,500 Pound Axles and Sure-Lube System

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching