Dimensions of Curt Trailer Hitch Receiver 2-1/2 Inch # 15802

Question

Question:

Looking for the specs on this hitch? Bolt hole center to center measurements and from mounting surface to top of receiver tube? Thanks! Tony

asked by: Tony J

0

Expert Reply:

The Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" # C15802 has 3 different hole dimensions for mounting. The two holes closest to the receiver are 36.31 inches on center. The widest holes are 37 inches on center and the most forward holes are 36-1/5 inches on center. The dimension from the frame rail to the top of the receiver tube and crossbar is 5-1/4 inches.

I've attached a photo to assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

I highly recommend the Curt Trailer Hitch #C15802 for your 2019 Ford F-250 Super Duty because it is a bolt-on installation that will not require drilling into your truck's frame and has the highest tongue weight capacity of any available…

view full answer...

Answer 2

If your bumper-pull toy hauler trailer has a tongue weight (TW) of 1400-lbs without your vehicles loaded (but with full water and propane tanks) usually the TW after you load ATVs will remain pretty much the same or potentially drop slightly. This…

view full answer...

Answer 3

The highest capacity trailer hitch we offer for your 2019 Ford F-250 is the Curt Class V hitch part #C15802 which has the towing capacity of 20,000 lbs and a tongue weight capacity of 2,700 lbs. It has a 2-1/2 inch hitch opening size and is also…

view full answer...

Answer 4

With the Curt hitch part #C15802 installed on your 2017 Ford F-250 you will definitely have a higher capacity hitch that would not be the weak point in your towing setup. It can't give you more capacity than the truck has but the added capacity…

view full answer...

Answer 5

Yes, the Curt Trailer Hitch Receiver #C15802 does fit your 2022 Ford F-250 Super Duty. This is a class V hitch with a gross towing weight of 20,000lbs and a maximum tongue weight capacity of 2,700lbs. If you need a ball mount, a great option is the…

view full answer...

Answer 6

Yes. For your 2017 Ford F-250 6.7L diesel, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2" #C15802 which is rated for tongue weights up to 2,700 lbs. This won't increase the tongue weight range of…

view full answer...

Answer 7

If you have the 6.2 V8 engine in your 2017 Ford F-250 Super Duty than the maximum tongue weight rating is 1,500 lbs and you would not benefit from replacing the factory trailer hitch but if you have the 6.7L V8 engine then the maximum tongue weight…

view full answer...

Answer 8

According to my contact at Curt, the distance from the mounting flanges to the top of the receiver on the Curt Class V Trailer Hitch, #C15317, is 7-1/4 inches. This hitch was designed to fit the Chevrolet and GMC C/K pickup trucks from 1988-2000 with…

view full answer...

Answer 9

I just went out to the warehouse and measured the Curt Trailer Hitch Receiver item #C15845. I have attached a couple of diagrams with the dimensions of this hitch on them. From the center of the back bolt to the front of the receiver is 26" The…

view full answer...

Answer 10

I was able to get a dimension sheet from my contact at Curt for the Curt Hitch part #C15800 that you referenced. See attached pic. I also attached a set of the installation instructions for this hitch.

view full answer...

Answer 11

Curt 2-1/2-inch Class V hitch #C15845 will fit the 1999 Ford F-450 cab and chassis so long as the frame width (measured outside to outside) is 34-inches. Drilling is required for installation. I went to our warehouse and measured the side-to-side…

view full answer...

Answer 12

According to TorkLift, the inside width of their #TLF1008-30 SuperHitch is 39-9/16 inches, measured from inside to inside of the mounting flanges as shown in the provided photo.Given that, your 37's should fit okay within the footprint of the…

view full answer...

Dimensions of Curt Trailer Hitch Receiver 2-1/2 Inch # 15802

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching