Does Curt Trailer Wiring Harness # C56217 Fit 2017 Highlander Hybrid

Question

Question:

Will this work with the Hybrid model? I have a 2017 Highlander Hybrid Limited. I couldn’t find any past Q and A regarding the most recent Hybrid model. Thanks

asked by: Jim

0

Expert Reply:

Yes, the Curt trailer wiring harness part # C56217 that you referenced does fit the 2017 Toyota Highlander Hybrid like what you have.

expert reply by: Jameson C

0

Answer 1

I did some research and I checked the Curt website to see if you can get the converter for your 2017 Toyota Highlander separately. You will have to get the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part #C56217, to…

view full answer...

Answer 2

For your 2016 Toyota Highlander with factory tow package the 4-pole wiring harness you can use is Curt part #56042. This uses a square connector (shown in the linked photo) that plugs in at the rear cargo area. The connection point is located behind…

view full answer...

Answer 3

I am happy to help you determine if your 2019 Toyota Highlander has a tow package or not. The easiest way is to visually inspect your vehicle on your own. If you take a look at the video for part #118449 that I attached on a 2019 Toyota Highlander…

view full answer...

Answer 4

Basically what it boils down to is that if you have the tow package you'll already have a 4-Way trailer wiring connector on your 2019 Toyota Highlander so if you don't already have one odds are you need a wiring kit with the converter like…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...