Replacement RV Waste Valve to be Used with Cable Handle

Question

Question:

I have a cable actuated rv Valterra waste valve. I need to replace the valve portion. will the Code T1003PBC part work for me. I do not need the cable, just the valve portion.

asked by: Mark C

1

Helpful Expert Reply:

The Valterra Waste Valve # T1003PBC is designed to be used with a cable handle so it will work well for you.

expert reply by: Charles S

1

Answer 1

The #T1003PBC valve is the one you will need for your sewer plumbing. We refer to it as valve body, because it does not include the handle, which you need to operate. Since you have indicated you have a 18 inch extension handle the #T1003PBC is the…

view full answer...

Answer 2

The waste valve part #T1003PBC is designed to be used with a cable handle like #TC96PB for a 96 inch cable or #TC72PB for a 72 inch cable. These are all black handle as there isn't a gray handle setup for this valve.

view full answer...

Answer 3

I do have an option for you, however the exact valve body that is included with the Valterra Waste Valve w/ Flexible Cable #TC372 you mentioned is not available as a separate part from the manufacturer. What you can use instead is the Valterra Waste…

view full answer...

Answer 4

The Valterra Waste Valve Extension Tube with Handle #TX9HPB can be used as a replacement, but they do thread in (see accompanying photo). If you can no longer thread in a rod, you are going to need to replace your waste valve with something like the…

view full answer...

Answer 5

Yes, the cable of your old waste valve can be used with your new Valterra Waste Valve Body w/ Flexible Cable for RV Gray Water Tank - 72" #TC172. The cable simply gets pushed into the valve body and tightened down with an Allen key (pictured…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 9

Unfortunately LaSalle Bristol completely covers the connection point in plastic so the only way to gain access to gate inside the LaSalle Bristol Cable-Actuated RV Waste Valve #34466N4BB96GM would be to cut into the plastic for the cord and…

view full answer...

Answer 10

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...