Generator Recommendation for RV with 13,500 btu AC Unit

Question

Question:

Will the AI SUA2300I RUN A Dometic Briskair2 13500 BTU RV AC?

asked by: Mike

0

Expert Reply:

For a 13,500 btu AC unit like the Dometic Brisk Air 2 you'd need a starting wattage of right at 3,000 watts. For that your best option is the A-iPower 3,800-Watt Portable Inverter Generators - 3,000 Running Watts - Gas - Manual Start # 289-SUA2000i-2.

The # 289-SUA2300I does not have the wattage you'd need as it can only put out 2,300 starting watts.

expert reply by: Jameson C

0

Answer 1

Yes the Maxxair Remote part #MA00A01150K is compatible with the Maxxair vent assembly MA00-05100K that you referenced.

view full answer...

Answer 2

Hey George, with the Reese weight distribution system part #RE94FR you can back up with the spring bars installed only if you are going to be basically backing up in a straight line. If you are going to jackknife the trailer at all though the bars…

view full answer...

Answer 3

For the SAE AP2 99 DOT lens we know that the part #A2RB is the correct replacement.

view full answer...

Answer 4

The best option for a trailer hitch receiver for your Chevy 4500 shuttle bus is going to be a weld on/bolt on option like you said, and the correct one will simply depend on the width of your frame from outside to outside, and the height of the…

view full answer...

Answer 5

I looked up the tongue weight of the Rockwood Roo 233S and for a weight distribution system that would work great with it's 500 lb dry tongue weight we have the Reese Pro Round Bar System part #RE94FR which has a tongue weight range of 400-800…

view full answer...

Answer 6

Thanks for that excellent info, and we do have an option for you, though the Dexter E-Z Flex #K71-656-00 actually has two different size equalizers, one that is 7-1/4" long and the other that is 5-3/4" long (from bolt hole to bolt hole) so…

view full answer...

Answer 7

If you can't place any weight on the trailer in any way that limits a lot of the options. Basically you'd have to decide if you could fit in in the interior or use a bunk like part #CC-255 as a platform on the tongue of the trailer. This is…

view full answer...

Answer 8

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 9

Load range D has a capacity of 1,220 lbs at 65 psi, whereas load range E has a capacity of 1,520 lbs at 80 psi. Basically the only difference between the two is the weight capacity. With trailer tires you always want to have them inflated to their…

view full answer...

Answer 10

Your R-pod has a Dometic system with a low profile that is 13,500 btu. The Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners - White #AT3308046006 is what I believe you need for your shroud. I've linked a video to…

view full answer...

Answer 11

Trailer or automotive wheels can have a positive or negative offset. The offset refers to the distance between the mounting surface of the wheel that touches the hub and the center line of the wheel, as shown in the diagram I have edited for you. A…

view full answer...

Answer 12

I called my contact at Curt and asked about the torque needed for the ball that the sway control is attached to on the trailer hitch. They told me that there has never been a torque listed but if you would torque it to about 150 ft-lbs it will have…

view full answer...