Replacement Reverse Lockout Solenoid Compatible with Titan Ultra-70 Brake Actuating Coupler

Question

Question:

I am looking for a solenoid back up valve for TITAN ULTRA-70 ACTUATOR. The number part is 4819300, but I can not find anywhere. Could you help me, please? Thank you

asked by: Cristian

0

Expert Reply:

That part number is not something we carry, however we do have the Replacement Solenoid Valve for Titan Brake Actuators with Reverse Lockouts # T4748800 which will work very well as a replacement for that solenoid. One wire is connected to your reverse light power wire at your trailer connector and the other wire is connected to the frame as a ground.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hey Dave, To retract the breakaway cable, slide the coupler fully forward and push up on the pushrod release bracket located on the underside and behind the hitch ball socket to allow the bead to retract into the actuator. This will release the…

view full answer...

Answer 2

As long as your trailer has a 3" x 5" trailer tongue then the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX56FR will replace your Titan Aero 6000 Coupler. Keep in mind this actuator is designed for disc brakes, so if you have…

view full answer...

Answer 3

There are only 3 real possibilities for your lockout failing to work properly on the #DX29FR. The first would be the power. Since it sounds like you are getting 12V power to the solenoid it doesn't sound like this is the issue. The second would…

view full answer...

Answer 4

The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX56FR you were looking at is confirmed to work with tandem axle trailers like yours, and is a great option as long as your trailer uses disc…

view full answer...

Answer 5

If the solenoid is getting a full 12 volts and is grounding properly it should be shutting all the way. Since you said it is clicking that makes it sound like it's getting power. You could try improving the ground circuit but most likely…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

Your surge coupler will have either a sticker or an engraving on it, typically near where the coupler is located. If you can get me that information and what you're needing to replace on it I'd be more than happy to help you find what…

view full answer...

Answer 11

Yes, you can weld on the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K item #DX56FR you referenced. You will want to make sure you remove the zinc coating and get down to the bare metal. I have…

view full answer...