Troubleshooting No Trailer Connected Issue with Factory Integrated Brake Controller

Question

Question:

2008 2500HD Silverado Duramax ITBC For quite a while now I have had an intermittent problem with my truck sensing the trailer connection. Sometime I would have to plug and unplug the trailer into my truck several times before I would get the Trailer Connected message on the dash. The problem has gotten worse and worse and now I cannot get the Trailer Connected message at all and I have no trailer brake operation. I had my friend plug into my trailer with his truck and no problems at all. This tells me the problem is not my trailer but it is my truck. I have replaced the trailer brake relay in the rear of the truck. I replaced the brake switch on the brake pedal. I am wondering if it could be the factory installed ITBC in the dash. Any Thoughts?

asked by: Dan

0

Expert Reply:

Normally when you are having a trailer connection issue, it is because there is corrosion or debris in the connection. The 7-way trailer connector on your truck at the 5 o'clock pin position is the brake controller output. This pin is where the brake controller will see a slight draw when the trailer is connected. Over time, build up on the pins will cause the vehicle not to sense the trailer so you may simply need to clean that connection with some sand paper or steel wool and then use some dielectric grease like # 11755 to keep the connection from that issue in the future.

The other possibility is that there is no power getting to that pin due to a short in the wire. You can test this with a circuit tester like # PTW2992. With the circuit tester grounded to your frame and the probe on the 5 o'clock pin, you should see a trailer connected message and be able to hit the manual override on the controller to see the voltage increase and the light in the tester get brighter. If you do not see this after cleaning the trailer pins, then you will want to trace that brake output wire probing every few feet to test for function to determine the short. To determine if it is a factory brake controller issue you will want to test the brake output wire under your dash close to the brake controller connection. If you have signal there, you may want to simply run a new wire # 10-1-1 from that point back to the pin location.

If you don't have power from the factory brake controller, you will either want to take it in to the dealer for repair or replacement or I recommend replacing it with # 90195 which is far superior to that factory integrated brake controller.

expert reply by: Jason S

0

Answer 1

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is…

view full answer...

Answer 2

I must recommend that you replace the hub/drum as well when changing the size of your braking assemblies because the surface area on the old drums may not line up with the new braking assemblies which is why I recommend replacing both at the same…

view full answer...

Answer 3

Hey Mike! Welcome back that is a great question. I am a big fan of both and at the end of the day they serve the exact same function as proportional braking systems. The main difference is going to be the installation process you're concerned…

view full answer...

Answer 4

The B&W Companion sliders like the #BWRVK3400, are height adjustable between 17" tall and up to 19" tall. There are a number of B&W Companion hitches available that have been tested and confirmed a fit on the 2020 Silverado 2500, so…

view full answer...

Answer 5

I checked out pictures of the rear of your Reflection 337RLS and I don't see why you would need an extension to use the Hollywood Racks RV Rider Bike Rack part #HLY64FR. This rack has quite a bit of extension between the hitch pin and the nearest…

view full answer...

Answer 6

The Timbren #TGMRTT35D are 5-9/16" tall.

view full answer...

Answer 7

We do have air bags available that are compatible with an in-bed hitch and also a fit for your 2022 Chevrolet Silverado 2500. I recommend the Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle #F2613. These air helper springs have…

view full answer...

Answer 8

The difference between the Timbren Rear Suspension Enhancement Systems #TGMRTT35D and #TGMRCK25D is that the former is designed for service vehicles, like tow trucks, while the latter is more for the average user. Since you have a 2019 Chevy…

view full answer...

Answer 9

Based on my research the issue with installing a factory brake controller on your Silverado (post-factory) has to do with the factory harness and programming on the truck. Chevy's official stance is that it cannot be added after the fact. You…

view full answer...

Answer 10

The "Trailer Disconnected" error message on the dash with a factory brake controller is usually related to an issue with the blue brake output wire that runs from the brake controller to the 7-Way connector. The fact that the issue remains…

view full answer...

Answer 11

I recommend checking out the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes #HLY64FR for your 2019 Winnebago Spirit. This bike rack measures 14-1/2" from the center of the hitch pin hole to the center of the wheel hoop, which should…

view full answer...

Answer 12

For your 2020 Chevy Silverado 2500 short bed with the factory puck system I highly recommend the B&W OEM Companion Slider #BWRVK3775. I like an awful lot about this particular hitch but some of the features that really stand out are its 1"…

view full answer...

Troubleshooting No Trailer Connected Issue with Factory Integrated Brake Controller

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching