Will Fulton Bolt-Thru Jack Fit in Place of Shelby Jack

Question

Question:

I need to replace this SHELBY trailer jack. As you can see it is welded on the trailer frame Was hoping I could locate a replacement and simply remove the bolt and put on the new one. any suggestions?

asked by: J P

0

Expert Reply:

I went out to the warehouse and took a few measurements of the mounting bracket on the Fulton Bolt-Thru Swivel Marine Jack # FXP10W0301 and found that the widest part of the indented hole is 1-12" while the hole that the bolt goes through measured 3/4". I have attached some pictures that you can use as a reference. If these match with your current Shelby jack then you can use the Fulton jack with your current mounting bracket that is welded to your trailer frame.

expert reply by: Jon G

0

click to enlarge

Answer 1

I can't see any part numbers or manufacturer names from your picture, but the Fulton XLT #F141132 does look very similar. I went out to the warehouse and measured the bracket that the bolt, washer, and nut go through for the installation. The…

view full answer...

Answer 2

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 9

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I was able to find the OEM part number for the Chevy spare tire hoist but I was unable to find a weight capacity rating on it. The owner's manual for the 2015 Chevy Silverado 1500 and the original hoist can handle the weight of a full sized spare…

view full answer...

Answer 12

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Will Fulton Bolt-Thru Jack Fit in Place of Shelby Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching