Can the Fulton XLT # F141132 be Used as Replacement Jack on a Centurion Boat Trailer

Question

Question:

Is this a direct replacement for my Centurion boat trailer jack?! Fulton F141132

asked by: Justin

1

Helpful Expert Reply:

I can't see any part numbers or manufacturer names from your picture, but the Fulton XLT # F141132 does look very similar.

I went out to the warehouse and measured the bracket that the bolt, washer, and nut go through for the installation. The wider inside measured about 1-5/8" while the outside hole measured 3/4" as you can see in the attached photo.

expert reply by: Jon G

1

click to enlarge

Answer 1

The correct replacement for the Fulton Magnum Series Trailer Jack on your trailer is the Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 if you have a bolt-thru mounting bracket or part #FTJ120W0301 if you have a snap-ring mounting bracket. I…

view full answer...

Answer 2

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Answer 3

The Xtreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels #ORJW350D does not come with the bearings installed. You can use something like a rubber mallet or a block of wood and hammer to tap them into place until they are flush.

view full answer...

Answer 4

I would be happy to help, but I have no way of looking your trailer by the serial number to determine which replacement side mount jack is correct. Based on the picture you provided of the jack on your Dorsey Malibu Boat Trailer a standard bolt on…

view full answer...

Answer 5

The Dutton-Lainson Square Swivel Jack #DL22340 has a mounting plate designed to fit trailer frames with a height of 3" - 5". I have attached a dimensional drawing below with all of the bolt spacing for your reference.

view full answer...

Answer 6

Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…

view full answer...

Answer 7

Yes, the Extreme Off-Road Swing-Up Jack w/ Dual Wheels iItem #ORJW500D will work for your T@B 400 Tear Drop Trailer. It looks like your trailer comes with an a-frame jack. You would need to ensure you have enough space on your tongue to accommodate…

view full answer...

Answer 8

The Extreme Off-Road Swing-Up Trailer Jack w/ Dual Wheels, #ORJW350D has an overall length of 18".

view full answer...

Answer 9

Load range D is likely the highest you will find on an ST175/80R13 tire. This is going to be a significant capacity increase over your current tires. Your typical load range C has a max load of 1,360 lbs per tire at 50 psi while a tire like the…

view full answer...

Answer 10

Does the welded on bracket on your trailer look like the part #P9012-00? If so, then you would want the part #F141132 for a Fulton XLT jack that would bolt right up to your trailer. If not, then you could pretty easily remove the bracket and install…

view full answer...

Answer 11

If you measure the distance between the mounting holes on the bracket you have on your trailer, and they do not match the mounting holes on your F2 jack you may need to have the old bracket removed and use a mounting bracket like part #F500277 for…

view full answer...

Answer 12

Fulton bolt-through trailer jack #F1411300301 is the only Fulton jack that mounts using that 1 center bolt. Since your old jack was a Fulton it must either be this same jack or an earlier model but they use the same mount. The mount in question and…

view full answer...

Can the Fulton XLT # F141132 be Used as Replacement Jack on a Centurion Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching