Trailer Hitch Mount Vehicle Recovery Rated for 34,000 Lbs

Question

Question:

Do you guys have a 2x2 shank with 2 inch screw hole for a bigger shackle, I have a 35 ton shackle with 2 inch screw

asked by: Lawrence

0

Expert Reply:

The Receiver Mount Shank for Big Dog Shackle part # BDW20181C001 is currently the only shackle shank we offer. Therefore, if you need a shackle shank with a 2" diameter hole you would need to drill out the 1-3/4" diameter hole that is already on the unit. If not we have the Bulldog Winch Shackle part # BDW20188 which is a confirmed fit and has a 34,000 lb working load limit (WILL).

I have attached review videos for you as well.

expert reply by: Conner L

0

Answer 1

For your 2002 Ford F-Series Super Duty we have the Torklift hitch part #TLF1002-30 which is a confirmed fit that has an upper hitch size of 2-1/2 inch by 2-1/2 inch and a lower that is 2 inch.

view full answer...

Answer 2

The Bulldog Winch 2" x 2" Receiver Mount Shank for Big Dog Shackle #BDW20181C001 doesn't have it's own weight rating but since it's designed for use with the Bulldog Winch Shackle #BDW20188 we can say that the shank is rated for…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

The best replacement pin box for the Lippert 1621 on your Grand Design Reflection 303RLS is the Curt Flex Air. This pin boxes has an air spring and shock absorber which will reduce the back and forth chucking (stopping and taking off) and lower the…

view full answer...

Answer 7

Yes. You will have to use the Demco Hijacker Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 on your 2021 Grand Design Reflection 337RLS. As far as which Curt Flexair works for your trailer, it depends on what pinbox you currently…

view full answer...

Answer 8

The shortest gooseneck ball we have for the 2024 Chevy puck system is the Reese Elite Series Pop-In Ball #RP23FR. This is going to be very similar to the Curt ball you mentioned. I have included some dimensions of the Reese ball below. From the top…

view full answer...

Answer 9

The Edge Pulsar programmer and monitor part #EP54KR can give you up to an additional 136 horsepower and 291 ft lbs of torque.

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

We still recommend the use of a slider in all standard/short bed trucks. That being said, the new GM trucks like your 2022 GMC Sierra 2500 do have a slightly longer bed than the typical standard bed. The best thing you can do is to measure to see if…

view full answer...

Answer 12

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...