How to Convert Yakima Holdup For 2 inch Hitch to Fit 1-1/4 inch Hitch

Question

Question:

I have a Yakima Holdup with a 2inch tongue and my new vehicle is a 1 1/4inch receiver. I want to replace the tongue to 1 1/4 but confused which part # I actually need. Can you please confirm the correct? Thank you

asked by: Wayne C

0

Expert Reply:

To convert a Yakima Holdup bike rack designed for a 2 inch hitch to fit a 1-1/4 inch hitch you'd want the part # 8880581 and you'd be set.

expert reply by: Jameson C

0

Answer 1

In order to convert your Yakima HoldUp #Y02445 to be compatible with a 2 inch hitch, you would only need the Replacement Tongue for Yakima HoldUp Bike Racks #8880580, which is a 2 inch tongue.

view full answer...

Answer 2

To convert your Yakima HoldUp 1-1/4" Bike Rack, part #Y02445, to be used with a 2" receiver, you absolutely can use the Replacement Spine for Yakima HoldUp Bike Rack for 2" Hitches, part #8890277. This spine is perfectly compatible…

view full answer...

Answer 3

You will need the Yakima Replacement Spine Assembly for 2 inch HoldUp Bike Racks, item #8890277, to replace the shank on your 1-1/4 inch HoldUp rack and make it work correctly in your 2 inch hitch.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...