How to Use the 1-1'4" Yakima HoldUp with a 2" Receiver

Question

Question:

Great- so it will include all the parts and I don’t need a new pin etc?

asked by: Justin

0

Expert Reply:

To convert your Yakima HoldUp 1-1/4" Bike Rack, part # Y02445, to be used with a 2" receiver, you absolutely can use the Replacement Spine for Yakima HoldUp Bike Rack for 2" Hitches, part # 8890277.

This spine is perfectly compatible with your HoldUp and is the recommended way of using that rack with a 2" receiver. I've linked to a video review of it below.

expert reply by: Kef G

0

Justin

4/8/2021

Great- so it will include all the parts and I don’t need a new pin etc?

Reply

Kef G.

4/8/2021

Actually, you will need the Replacement Hitch Hardware for Yakima HoldUp Bike Racks, part # 8890260, since the hardware from the 1-1/4" shank will not work and the new spine does not include this. I apologize for not noticing this before, but those two pieces will be all that you need.

Reply

Answer 1

In order to convert your Yakima HoldUp #Y02445 to be compatible with a 2 inch hitch, you would only need the Replacement Tongue for Yakima HoldUp Bike Racks #8880580, which is a 2 inch tongue.

view full answer...

Answer 2

To convert a Yakima Holdup bike rack designed for a 2 inch hitch to fit a 1-1/4 inch hitch you'd want the part #8880581 and you'd be set.

view full answer...

Answer 3

You will need the Yakima Replacement Spine Assembly for 2 inch HoldUp Bike Racks, item #8890277, to replace the shank on your 1-1/4 inch HoldUp rack and make it work correctly in your 2 inch hitch.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...