Where to Locate Manufacture Date on an Extang Trifecta Cover for a 2014 Ford F-150

Question

Question:

I need to order a replacement soft top. However, I purchased my 2014 Ford F 150 in 2014 and I was given a Trifecta by a friend of mine. I have no idea when it was made...prior to or after November of 2010. And my friend cannot remember if it before or after 2010. Is there any way for me to find that out on the frame of the unit?

asked by: Roger

0

Expert Reply:

If you look at your current cover you should be able to find the manufacture date towards the cab side of the cover. Let me know if your 2014 Ford F-150 is the 6-1/2' bed or the 5-1/2' bed and if it has the cargo management system and I can let you know what replacement tarp you are needing.

expert reply by: Jon G

0

Answer 1

There is a replacement tarp for an Extang Tuff Tonno Tonneau Cover that fits a 1995 Ford F-150 with a short bed, but the part number you referenced is a replacement tarp for a Tuff Tonno on certain Dodge Rams. Instead, you will need one of two…

view full answer...

Answer 2

We have some Exfang Trifecta Tonneau Covers that come with replacement vinyl tarps. It depends though on the size of your bed as well as when your tonneau cover was manufactured. For the Original Extang Trifecta for 2003 Ford F-150 with a 6-1/2 foot…

view full answer...

Answer 3

For your 2010 Ford F-150 with 6-1/2 foot bed, the Extang Trifecta replacement cover is #EX92410-20.

view full answer...

Answer 4

The Replacement Tarp for Extang Trifecta 2.0 Soft Tonneau Cover #EX92410-20 is the correct replacement tarp for the Extang Trifecta 2.0 Soft Tonneau Cover #EX92410 which is confirmed to fit your 2013 Ford F-150 with 6.5' bed and no cargo…

view full answer...

Answer 5

I am happy to determine the replacement cover for you but I would need the serial number off of your older Extang cover. The easiest way is to locate the serial number. Most of the time the serial number can be found on the driver's side front…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Where to Locate Manufacture Date on an Extang Trifecta Cover for a 2014 Ford F-150

Product Page this Question was Asked From

Continue Researching