How to Pick Out Boat Trailer Hub for TrailStar Boat Trailer
Question:
Good afternoon, I am looking for replacements for my boat trailer hubs. They are TDE 46205 if that helps any. They have 5 studs and 4.5inch as far as I can tell. Would there be a direct replacement available that a fellow could order? Any help would be appreciated.
asked by: Jeremy D
Expert Reply:
In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information. The first thing you will need to know is the bolt pattern of your hubs. This is so you get a hub that is compatible with your wheels. I attached an FAQ article on determining bolt pattern for you to check out.
Next thing you will need to know is what spindle you have on your trailer. In order to do that you can either get the inner and outer bearing numbers from a hub or use a dial or digital caliper to get exact measurements of the spindle. The measurements needed are the parts of the spindle where the bearings ride.
If you get back to me with that information I will help you pick out the right hub assemblies. Or, you can follow the link I attached that will take you to the page that has all of our replacement hubs.
You would want to first select the bolt pattern that you have, next select the inner bearing you have, followed by selecting your outer bearing, and then all the correct hubs will be listed.
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Pre-Greased
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Q&A: Replacement Trailer Hub for the TDE 46205 with Galvanized Finish
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Pre-Greased
- Q&A: Trailer Hub Assembly Must be Put Together and Packed with Grease
- Search Results: bunk bracket
- Search Results: cable
- Search Results: terminal box
- Search Results: 7 way cable
- Search Results: anchor points
- Shop: Shackle Strap - 3-1/8" Long
- Shop: Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
- Shop: 7-Way Molded Connector w/ 15' Cable - Trailer End
- Shop: Trailer Wiring Junction Box - 7 Terminals - Polypropylene
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-545-2-G-1K Review
- Search Results: 3 leaf trailer leaf springs
- Search Results: 3 leaf slipper spring
- Q&A: Is Bushing Required on Open Eye End of Slipper Spring
- Shop: Trailer Hitch
- Q&A: How to Read the Lippert Components Axle Description Measurements
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How to Measure Hub Face of Mobile Home Hub and Drum
- Q&A: Replacement 5 Leaf Slipper Spring for a Tandem Axle Dump Trailer with Two 6K Axles
- Shop: Fifth Wheel Hitch
- Video: Choosing the Right Trailer Wiring
- Article: Most Popular Wheel Bearings
- Shop: Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)