How Much Will Springs of the Timbren Silent Ride Suspension # TSR3500S04 Compress Under 2K lbs

Question

Question:

How much will these compress with a static trailer weight of 2000 pounds. I need to know for ride height. Also are they designed to be trailing arm or can they be mounted as leading arm.

asked by: Mike B

0

Expert Reply:

The Timbren Silent Ride Suspension # TSR3500S04 will have about 1" to 1-1/2" of compression with 2,000 lbs of trailer weight and they are designed to be trailing arm. I confirmed this with my contact at Timbren.

expert reply by: Jon G

0

Answer 1

According to my research, your T@B trailer has torsion axles which means the Timbren Silent Ride Suspension System like part #TSR3500S05 will not be a good fit for you. Instead, you will want to use the Timbren Heavy-Duty Axle-Less Trailer…

view full answer...

Answer 2

The Timbren Silent Ride #TSR14KT01 can actually be installed by welding it on or bolting it on. You could do both welding and bolt it on, but that is not really necessary. I am not sure of the bracket to move it around on the frame, but they do…

view full answer...

Answer 3

The Timbren Silent Ride Suspension for Single Axle Trailers w/ 2-3/8" Round Axles - 2,000 lbs #TSR2000S03 that you referenced has an axle capacity of 2,000 lbs as a pair. Or individually each side would have a capacity of 1,000 lbs.

view full answer...

Answer 4

Yes, the Timbren Silent Ride Suspension Systems like part #TSR2000S03 require a crossmember installed between driver and passenger side. The crossmembers is needed to add additional support. It will be welded to the back of the flange which you can…

view full answer...

Answer 5

National seal 472920 has an inner diameter of 2.25 inches and outer diameter of 3.375. For a replacement, you will want Grease Seal - Double Lip #GS-2250DL or oil seal #10-63.

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 8

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 9

The shackles like the #TRSL225 are bare steel. With enough contact with moisture they will begin to show signs of surface rust. Especially on a boat trailer that backed into saltwater.

view full answer...

Answer 10

The TSS-105-40 is no longer available from SuperSprings. You are going to need their current SumoSprings Trailer Helper Springs #TSS-106-40 for your Coachmen Apex Nano 193BHS. This kit is designed for underslung axles with a capacity between 3,000lbs…

view full answer...

Answer 11

I do have an option for you but we do not currently offer a Dexter straight axle with the spring center and hub face dimensions that you provided. However, we do have the Timbren Axle-Less Trailer Suspension System part #TASR5200S03 which will…

view full answer...

How Much Will Springs of the Timbren Silent Ride Suspension # TSR3500S04 Compress Under 2K lbs

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching