Hidden Hitch Recommendation for a 2002 Toyota Tacoma
Question:
The step bumper on our 2002 Toyota Tacoma measures a width of 3 5/8 in. My question is will the Curt E3-S bumper hitch work as I would have to re-drill the rear 2 holes maybe 1 in. inwards. The E-3S is 4inch front to back. The bumper is 3 1/2 If not re-drilled the holes would be too close to the edge, so I would have to compensate for the 1/2inch difference. I could stagger the new holes as not to be too close to the existing holes. What do you think? Thanks,
asked by: GARY B
Expert Reply:
I think that your best bet would be to install a hitch that installs onto the frame of your 2002 Toyota Tacoma, like a Draw-tite Trailer Hitch Receiver # 75078. Not only will you have a much higher towing capacity, you will not have to make any permanent modifications to your vehicle bumper that might void the warranty of the vehicle.
I attached installation instructions and a review video for this product for you to check out also.
To complete your towing setup you may be interested in the following products:
etrailer Ball Mounts # 989900
Draw-Tite Custom Fit Vehicle Wiring # 118379 (installation instructions and video attached)
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 5500 lbs WD GTW
- 2 Inch Hitch
- 550 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Curt 2" Trailer Hitch - Bumper Mount - 8-3/4" Bolt Pattern - 5,000 lbs GTW
- Bumper Hitch
- 500 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Bolt-On
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Wiring
- Shop: Front Mount Hitch
- Video: Best 2001 Toyota Tacoma Trailer Hitch Options
- Shop: Bumpers
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Video: Trailer Wiring Harness Installation - 2000 Toyota Tacoma
- Shop: Brake Controller
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Rise - 7,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Dexter Trailer Idler Hub Assembly for 5,200-lb Axles - 6 on 5-1/2
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Search Results: scissor jack
- Search Results: jack
- Search Results: bottle jack
- Search Results: scissor jacks
- Search Results: 2" ball
- Search Results: bulldog sidewind jack
- Q&A: Differences Between The 4-Way Wiring Options For 2002 Toyota Tacoma
- Q&A: 7-Way Recommendation for 2001 Toyota Tacoma with Reverse Light Circuit Active
- Article: Trailer Wiring Diagrams
- Shop: Towing Mirrors
- Search Results: 2" hitch
- Q&A: Is a Trailer Hitch Visible Beneath the Bumper Once Installed on a 1999 Toyota Tacoma
- Video: Curt Weight Distribution - WD With Sway Control - C17499 Review
- Shop: Camper Tie-Downs
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Video: Trailer Brake Controller Installation - 2012 Toyota Tundra