Replacement L-Pins for 6,000 Pound Equal-i-zer Weight Distribution System

Question

Question:

Will this part also work for 6,000 WDH?

asked by: Richard M

0

Expert Reply:

I do have an option for you, however the Replacement L-Pin # 90-03-9460 referenced in your question is only rated for the 4,000 pound Equal-i-zer Weight Distribution Systems like # EQ37040ET.

For your higher-rated 6,000 pound system, you will instead need the Replacement L-Pins and Clips # EQ95-01-9430. This includes 1 pair of L-pins with the needed integrated clips.

expert reply by: Chris R

0

Answer 1

I went out to our warehouse and measured the Replacement L-Pin for Equal-i-zer 4,000-lb Weight Distribution Systems #90-03-9460. The length of the long side is 2-1/2" long, the short side measured at 1-1/2" long and the thickness of…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this we…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...