Comparing TruRyde and Fulton Grease Caps for Trailer Hubs with 1.988 Inch Bore

Question

Question:

What is the difference between this part RG04-020 and F00-1518? Thanks

asked by: Paul W

1

Helpful Expert Reply:

There is basically no difference between dust cap set # RG04-020 and single cap # F001518 other than # F001518 is a single unit and # RG04-020. They otherwise have the same dimensions just from two different manufacturers.

expert reply by: Michael H

1

Answer 1

I would recommend to remove and reinstall the complete trailer hub assembly to make sure all of the parts are installed properly. I am including a link to a video of how to remove and reinstall a trailer hub on a boat trailer. This video will show…

view full answer...

Answer 2

The Grease Cap - 1.988" Outer Diameter part #F001518 is correct for a Dexter 10" Hub for 3,500 Axle.

view full answer...

Answer 3

The Rubber Lube Plug - Fits 1.18" Lubed Dust Cap #DC-RP is the replacement for the #RG04-040 grease cap as well as larger caps like the 2.44" OD Drive In Grease Cap with Plug #RG04-080. The Grease Cap Plug fro E-Z Lube Grease Caps…

view full answer...

Answer 4

The Grease Cap Plug for E-Z Lube Grease Caps - Qty 2 #RG04-010 is designed to fit in E-Z Lube axle caps that have a 1.18" diameter opening. If you don't have an E-Z Lube it's possible that if you're measuring the…

view full answer...

Answer 5

It's hard to see the diameter of your cap in the picture you submitted but it appears you need the part #DC-RP which fits a 1.18 inch diameter hole like it looks like you have.

view full answer...

Answer 6

You will want to use a dial caliper or micrometer like part #PTW80157 to measure the inner diameter of the hub you have on your trailer to determine what size cap would be needed. Check out the picture I attached that shows this measurement being…

view full answer...

Answer 7

We offer rubber grease cap plugs like #DC-RP which fits a 1.18-inch dust cap hole; this is sold as a single piece. We also offer a set of two in the same size as part #RG04-010. These fit grease caps like #RG04-040.

view full answer...

Answer 8

I do have an option for you but the Rubber Lube Plug part #DC-RP that you purchased is designed to fit a 1.18" diameter opening and will not work for you assuming the plug you measured is indeed 1.5" diameter. Instead, the better option for…

view full answer...

Answer 9

If the measurement you listed (2-3/32 inches) the only caps we offer that would work would be a Bearing Buddy part #BB2080SS. We do not have any standard grease caps that would fit.

view full answer...

Answer 10

With the measurements you got, the closest we will have is the #AH15450ECOMP. This is an agricultural hub the uses the outer bearing #LM11949, which does match the .75", but the inner bearing does not match. This uses a #LM67048 that has a…

view full answer...

Answer 11

If you are looking for a grease cap PLUG with the TRP stamped on it chances are the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 would work for you, but to be certain you will want to measure the diameter of the grease cap hole. If it is 1.18…

view full answer...

Answer 12

I'm assuming you're speaking of a grease cap that's driven into the hub bore. Grease caps are available in different sizes. There are two good ways to determine which size you need. One is to locate the reference number off of the outer…

view full answer...

Comparing TruRyde and Fulton Grease Caps for Trailer Hubs with 1.988 Inch Bore

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching