Trailer Hitch and Weight Distribution Recommendation for a 2010 Acura MDX and 5,000 Pound Trailer

Question

Question:

2010 acura MDX...I will tow near 5K vehicle max capacity and was going to buy a Curt 13354 hitch and 17300 equalizer would that be a good choice or would you recommend another...also is trunnion style really better?

asked by: Neil

0

Expert Reply:

The CURT Trailer Hitch, # 13354, would be a good choice for your 2010 Acura MDX. When used with weight distribution, it has a tongue weight capacity of 500 pounds and a gross trailer weight capacity of 5,000 pounds. I have included a link to the installation instructions and a link to a video showing a typical installation.

When choosing a weight distribution system, you will want to go with one that has a tongue weight capacity range that encompasses the tongue weight of the trailer when loaded and ready to tow. This also counts the weight of anything loaded behind the rear axle in the tow vehicle.

Tongue weight is usually 10 to 15 percent of the gross trailer weight. For a 5,000 pound trailer, that would put the tongue weight between 500 and 750 pounds. I recommend going with a system that is rated for 400 to 800 pounds to cover the whole span.

Take a look at the Reese Weight Distribution System, # RP66541. This is a trunnion bar system that includes the shank so you would just need a properly sized ball like # 19286 (2-5/16 inch diameter) or # A-90 (2 inch diameter). I have included a link to the installation instructions for you.

Trunnion bars are considered more heavy duty than round bars, but both types work well. I have included a link to our weight distribution FAQ article for you.

I would consider adding sway control to this system with a trailer this heavy. There are 2 types of sway control: friction and dual-cam. Dual-cam is preferred because it stops trailer sway before it starts. To add sway control to the system recommended above, use # RP26002. Or you can get them together with part # RP66083.

expert reply by: Michael H

0

Answer 1

You will need to start with a 4-way (if you do not have one) on your 2010 Acura MDX to install a 7-way and brake controller. For that you would want the #118424. From there you would need to convert the 4-way to a 7-way so that you can install the…

view full answer...

Answer 2

Yes, we have pictures and a video of the hitch on an Acura MDX and it is very low profile and out of the way. At this time we have not had the chance to get photos of the hitch on a 2009 model but the fit is the same as the 2010 model pictured. You…

view full answer...

Answer 3

In the USA a tandem axle utility trailer with a gross vehicle weight rating (GVWR) of 7500-lbs should have brakes installed. Any trailer over 3000-lbs must have brakes on all wheels in most states, but laws do vary. Some states require braked axles…

view full answer...

Answer 4

For your 2008 Acura MDX we have the Curt hitch part #13354 which is a confirmed fit, and if you check out the install picture I attached you will see that it does not extend past the rear bumper at all. It actually is recessed a few inches. I also…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...