Replacing Master Cylinder in Titan Model 10 Actuator on Boat Trailer
Question:
Looking at this master assembly it’s the one on my trailer but I can’t see how to get the master cylinder out as there are no exposed side bracket bolts to bolt it into place? Would they be that stupid to put frame rails over the bolts that hold the master into place? Would I have to cut holes into the frame rails to remove it? Should I rebuild it in place? I got the piston and seals out and it measures 1.25 on the fron cup and the piston seal? What can you tell me ? Thank you Chris K
asked by: Chris K
Expert Reply:
If the master cylinder you need is the part # T2374600 that would indicate that you have a Model 10 actuator like the part # T4750620. Which normally this bolts to the trailer frame. The picture you submitted doesn't quite show the coupler so I can't really tell what's going on. But you should be able to unbolt the coupler from the trailer to access the master cylinder and replace it.
The two lower bolt holes that I pointed out in the picture are what hold the master cylinder to the coupler.
Products Referenced in This Question
Dexter Zinc-Plated Brake Actuator w/ Drop, Electric Lockout - Disc - 2-5/16" Ball
- Brake Actuator
- Surge Brake Actuator
- Agricultural
- Construction
- Marine
- Travel Trailer
- Utility Trailer
- Bolt-On
- 12500 lbs GTW
- 2-5/16 Inch Ball Coupler
- Disc Brakes
- Electric Lockout
- Dexter
more information >
Product Page this Question was Asked From
Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Drum
- Accessories and Parts
- Brake Actuator
- Hydraulic Drum Brakes
- Master Cylinder
- Dexter
more information >
Continue Researching
- Shop: Replacement Master Cylinder Assembly for Dexter Model 10 and Model 20 Brake Actuators - Disc
- Shop: Replacement Solenoid Valve for Dexter Brake Actuators with Reverse Lockouts
- Shop: Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 1'
- Shop: Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 2'
- Shop: Kodiak Union Fitting for Hydraulic Brake Hose - Brass - 3/16" Female Inverted Flares
- Shop: Kodiak Hydraulic Brake Hose - Straight and 90-Degree Male Fittings w/ Stainless Flares - 1.5'
- Shop: Kodiak Hydraulic Brake Hose - 3/16" Male Fittings w/ Stainless Flares - 1/8" ID - 3.5'
- Search Results: brake fittings
- Search Results: brass fittings
- Search Results: boat trailer brake lines
- Search Results: trailer brake master cylinder
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Replacement Master Cylinder for 1990 Trail Rite Surge Brake Coupler
- Q&A: How To Replace Master Cylinder For Titan 10 Brake Actuator
- Video: Titan Master Cylinder Assembly Installation
- Video: Titan Brake Actuator T2374600 Review
- Video: Titan Brake Actuators with Reverse Lockout Replacement Solenoid Valve Installation
- Video: Titan Brake Actuator T1242600 Review
- Search Results: kodiak 225 brake caliper
- Video: Review of Kodiak Trailer Brakes - Disc Brakes Kit - K2HR526DKG
- Q&A: Recommended Disc Brake Kit For 20 Foot Boat Trailer
- Q&A: Replacement Master Cylinder for a Model 10 or 20 Brake Actuator
- Q&A: Can You Back Up With Titan Hydraulic Actuator Without Reverse Lockout
- Q&A: How to Remove the Master Cylinder Assembly on a Titan Model 20 Brake Actuator
- Q&A: How to Tell Difference Between Titan Model 20 Drum and Disc Actuator
- Search Results: surge brake actuator
- Article: How to Bleed Your Trailer Surge Brakes
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: brake line
on Accessories and Parts
