Amperage Draw of MaxxTow Off-Road Light # MT80637

Question

Question:

would like to know aprox. amp draw , and if it changes over an eight hour use. I`m wanting to use off-grid with solar and wind generation .

asked by: Alan C

1

Helpful Expert Reply:

The wattage of the MaxxTow Off-Road Light # MT80637 is 27 that means this draws 2.25 amps per hour. Depending the amp hour rating of your battery will dictate how long that would last.

expert reply by: Jameson C

1

Answer 1

It is possible to install driving lights, like part #MT80637-2, on a kayak with a 12-volt battery to power them. You'd just want to make sure they were installed in a way to keep water off them.

view full answer...

Answer 2

There isn't a formula for the wire gauge, you can simply match it up to the wire size used with this light, which is 14 gauge wire. I have added a link to a video review as well of the MaxxTow Off-Road Lights #MT80637-2.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It will depend on if you have a Westin Grille Guard or an Aries Grille Guard. If you have either of the Westin Sportsman Grille Guards, the black, part #40-0245, or the polished stainless steel, part #45-0240, you will need the following hardware…

view full answer...

Answer 8

Mounting hardware for brush guards is specific to both the brush guard and the vehicle. The fact that you pulled the brush guard off of a vehicle that is the same model and year is good news for finding compatible mounting hardware. That being said,…

view full answer...

Answer 9

Based on the photo you attached, it looks like you have either the Westin Sportsman Grille Guard - 1 Piece - Black Powder Coated Steel #40-0245 or the Aries Grille Guard - 1 Piece - Semi-Gloss Black Powder Coated Steel #AA3046. If you have the Westin…

view full answer...

Answer 10

The only way to remove a Thule lock cylinder like the ones in #TH450400 is by inserting the master key into a cylinder in the unlocked position. However, I have a few tips and tricks to help you remove the broken key to allow for the master key to be…

view full answer...

Answer 11

Due to the amount of coverage a grill guard or bull bar provides on the front of your 2020 Toyota 4Runner, installing any of these will interfere with the front sensors, including the Westin Sportsman Grille Guard - Polished Stainless Steel #45-3820…

view full answer...

Answer 12

Thanks for your purchase of the Westin Sportsman Grille Guard #40-3825 for your 2017 Toyota 4Runner! In order to install the MaxxTow Off-Road Lights #MT80637-2 on the grill guard you need a power source, wiring, a switch, and some connectors. For the…

view full answer...

Amperage Draw of MaxxTow Off-Road Light # MT80637

Product Page this Question was Asked From

Continue Researching