Spare Tire Carrier wtih Lock for 10 Inch Wheels.

Question

Question:

Almost all of your mounts say they will work for Application: fits 8, 9, 12, 13, 14inch and 15inch wheels with 4- or 5-lug rims 10inch wheels are not listed. I have a 10inch rim with a 5 on 4 1/2 pattern. Will these mounts work ?

asked by: Jon E

0

Expert Reply:

The Fulton spare tire carrier, part # FETCHL0700, will fit 10 inch wheels. It'll work just fine with your 10 inch wheels that have a 5 on 4-1/2 bolt pattern.

expert reply by: Charles S

0

Answer 1

I believe I have found the replacement wheel you are looking for. It's kind of hard to see in our product pictures but the Dexstar Steel Mini Mod Wheel part #AM20443 has a sticker on it that reads 17-231 and is a 15 inch diameter wheel with a 5…

view full answer...

Answer 2

I have a different option for you, but there is not a version of the etrailer Spare Tire Carrier #e99045 you were looking at that works with 2" square tubing on your trailer. The closest straight mount carrier is going to be the CE Smith Spare…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...