Height of Titan Zinc-Plated Leverlock Coupler

Question

Question:

Can you measure the maximum height of the coupler from the top of the lever to the base.

asked by: Joseph O

0

Expert Reply:

I took a measurement for you and the height of the Titan Zinc-Plated, Leverlock Coupler # T4845000 with the trigger latch up is approximately 6".

This coupler works with 1-7/8", 2" or 50 mm balls, mounts on a 3" wide tongue, has a 5,000 lb capacity and 500 lb tongue weight capacity.

expert reply by: Kyle S

0

click to enlarge

Answer 1

I attached a picture that has all of the dimensions you requested for the Titan coupler part #T4845000 that you referenced.

view full answer...

Answer 2

In order to engage the reverse lockout on the Titan Brake Actuator with Manual Lockout part #T63FR you will need to insert the lockout tool which is included, into the channel directly behind the coupler. I have pointed this channel out for you as…

view full answer...

Answer 3

You actually won't need to trim any rear fascia when installing any of our trailer hitches on your 2020 Toyota RAV4. Out of our selection I recommend going with the Class III Curt Trailer Hitch #C13416 because it has a 2" receiver (so it is…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Height of Titan Zinc-Plated Leverlock Coupler

Product Page this Question was Asked From

Continue Researching