How to Use a TorkLift SuperTruss Hitch Extension to Tow a Trailer with the Tailgate Down

Question

Question:

I would like to load a motorcycle in my truck bed which requires the tailgate to be down. Will this extension allow towing of a travel trailer with the tailgate down?

asked by: Jordan

0

Expert Reply:

For starters, the TorkLift SuperTruss Hitch Extension will only work if you have a SuperHitch Original, Magnum, or Hero already installed on your tow vehicle. These hitches have a dual receiver tube opening which is what allows them to work with the SuperTruss. If you need one then please let me know the year, make, and model of the tow vehicle.

In order to determine if the TorkLift SuperTruss Hitch Extension part # TLE1524 will work for you, you will want to measure from the center of the hitch pin hole to the outer edge of the tailgate while folded down. If this distance is less than 24" than this extension will be what you need. However, if it is not then you will want to consider a longer extension which I have attached a list of for you below

28" - part # TLE1528
32" - part # TLE1532
36" - part # TLE1536
42" - part # TLE1542
48" - part # TLE1548
60" - part # TLE1560

expert reply by: Conner L

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 4

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

If you have the Ford 3" hitch then you can definitely add it but, yes it would change the weight capacity. The TorkLift Cannon Hitch Extension item #TLE1636 only has a 3,600 lbs towing capacity and a 360 lbs maximum tongue weight. If used with a…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The Draw-Tite Front Mount Trailer Hitch Receiver #65076 will fit your 2023 Ford F-350 dually. It features a bolt-on installation and has a 2" receiver. The hitch has a 9,000 lb line pull, 500 lb vertical load, and 5,000 lb gross trailer weight.…

view full answer...

How to Use a TorkLift SuperTruss Hitch Extension to Tow a Trailer with the Tailgate Down

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching